Scrappycrow
Full Access Member From Alpharetta, Georgia
- Joined
- Last seen
- Viewing thread What did you do to your NNBS GMT900 Tahoe/Yukon Today?
Latest activity Postings About
-
-
Scrappycrow replied to the thread TPMS Wackiness: Had A Flat, Didn't Indicate it; Tire Is At Shop, Still Shows Pressure. What Gives?.Good idea, thanks! Just a few days ago, I picked up one recommended by folks here (OEC-T5 EL-50448 from Amazon). -
Scrappycrow posted the thread TPMS Wackiness: Had A Flat, Didn't Indicate it; Tire Is At Shop, Still Shows Pressure. What Gives? in Exterior.So, this morning I came out to a flat on my '13 LTZ. I must have picked up the screw within 1/4 mile of home, as it had little wear on...
-
Scrappycrow reacted to j91z28d1's post in the thread Tire Noise Reduction -- Any Experiences with Fender Liner and/or Fenderwell Treatments? with
Like.
in my C6 I bought a kit they sell. it had a bunch of large sections of dynomat and then a full foam core insulation kit. took like a... -
Scrappycrow reacted to gtrslngrchris's post in the thread Tire Noise Reduction -- Any Experiences with Fender Liner and/or Fenderwell Treatments? with Like.
I may have to give the extreme version a try but my guess is that it really comes down to how long it sits in the heat and since I'm in...
-
Scrappycrow replied to the thread Tire Noise Reduction -- Any Experiences with Fender Liner and/or Fenderwell Treatments?.Thanks for the warning! FWIW, I used Dynamat Xtreme on the BMW I mentioned earlier in the thread, and on the exhaust/gas tank heat...
-
Scrappycrow reacted to Charlie207's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
Flawless through the first 100 rounds, which is a pleasant surprise. Running S&B 230gr FMJ right now, and then will try some JHPs...
-
Scrappycrow replied to the thread Tire Noise Reduction -- Any Experiences with Fender Liner and/or Fenderwell Treatments?.No. The ResoNix Fiber Mat specs say: "Service Temperature (°F): -40 to +300 continuous; +375 intermittent" Even if not that...
-
Scrappycrow reacted to fozzi58's post in the thread Tire Noise Reduction -- Any Experiences with Fender Liner and/or Fenderwell Treatments? with Like.
My exhaust is pretty loud and I have a sub and amp. I installed Killmat in my truck and it made as big difference. I have not tried...
-
Can you post a picture and indicate EXACTLY where you added and ran the silicone bead?
-
Scrappycrow reacted to j91z28d1's post in the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today? with Like.
huh. I'll have to Google water level. the turn plates are worth it I tried a few didn't cutting board tricks but turn plates are cheap...
-
Scrappycrow reacted to jared999's post in the thread Does my radiator have an engine oil cooler? with Like.
All cooling systems are heat exchangers. I would think you can call them either or?
-
Scrappycrow replied to the thread Tire Noise Reduction -- Any Experiences with Fender Liner and/or Fenderwell Treatments?.Fresh tires are great, but most of their life will be non-fresh, thus I want a long-term solution. Yeah, a tire-side absorption layer...
-
Scrappycrow replied to the thread What did you do to your NNBS GMT900 Tahoe/Yukon Today?.My garage isn't flat, either, but I do all my alignments myself and make the floor "flat" under the tires with the use of a water level...
-
Scrappycrow replied to the thread Tire Noise Reduction -- Any Experiences with Fender Liner and/or Fenderwell Treatments?.@petethepug , I sure do know the value of these treatments! I have a relatively loud exhaust on my BMW E28 535i (dual 1.75" pipes...
-
Scrappycrow replied to the thread Tire Noise Reduction -- Any Experiences with Fender Liner and/or Fenderwell Treatments?.There won't be any issue with using Dynamat outside the cabin. The black gooey layer is butyl rubber, which is frequently used on the...
-
-
Loading…
-
Loading…
