clandr1
Latest activity Postings About
-
-
clandr1 reacted to mattbta's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with
Like.
Added some more boom booms. I converted to Lux Bose in my 2004 Hoe and last summer put a shallow 8 in a pre-03 factory box in the back... -
clandr1 reacted to latvius's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Yeah you gotta fix that first, it doesn't make sense to me to troubleshoot further until that is fixed and then test the brakes to see...
-
clandr1 replied to the thread What did you do to your NBS GMT800 Tahoe/Yukon Today?.I’m no expert but would have to think there’s either air, or a leak, in the system.
-
clandr1 reacted to Gmg0547's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
It has been a while but recently took a 1600 mile round trip from NC to CT with the family. The Yukon didn't miss a beat and made what...
-
clandr1 reacted to latvius's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
-
clandr1 reacted to strutaeng's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
I cleared these yesterday...just reinstalled them. Not bad, eh? I wonder if I should do the rear taillights on the suburbans now?
-
clandr1 reacted to strutaeng's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Finished my 6.0 LS engine I started building over 1 years ago! Installed pushrods, rockers and valve covers. L96 block with Gen III...
-
clandr1 replied to the thread What did you do to your NBS GMT800 Tahoe/Yukon Today?.@StrkAliteN you are in the 00-06 subforum, you'll need to post this in the 07-14 forum for better answers. Nice looking truck!
-
clandr1 reacted to NoReverseYukon's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
I was just trying to remove the knuckle, so all this BS was to get the tapered shaft of said ball joint out of the LCA. And even though...
-
clandr1 reacted to NoReverseYukon's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Getting that ball joint out of the lower control arm was quite the ordeal.
-
clandr1 replied to the thread What did you do to your NBS GMT800 Tahoe/Yukon Today?.Was this your first time? If so, did you grind down the retaining tabs before you started whacking the BJ? Also, as my dad always...
-
clandr1 reacted to MassHoe04's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Hi people!!! Been some time since last post here! Had to replace broken parking brake cable that snapped while testing just before I...
-
clandr1 reacted to Aquamania001's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Had the heater assembly lines replaced. Went from the water pump to the heater core. Noticed a slow leak from watching my expansion...
-
clandr1 replied to the thread What did you do to your NBS GMT800 Tahoe/Yukon Today?.This is incredible work - great job!
-
clandr1 reacted to treehan77's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Spray painted the carpet. Yes spray paint. It was heavily damaged by a 2 1/2 gallon container of pool chlorine (twice as strong as...
-
-
Loading…
-
Loading…
