Jimmyy's latest activity
-
JJimmyy reacted to latvius's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with
Like.
After I painted my rear bumper with the $4 rural king can of spray paint the orange peel was getting to me. So I busted out the wet... -
JJimmyy reacted to Fless's post in the thread There are just some days I wish I didn't turn wrenches with Like.
There can be a little slack in the connection to the outside handle especially if the handle spring is a little weak, so pulling down or...
-
JJimmyy reacted to Fless's post in the thread There are just some days I wish I didn't turn wrenches with Like.
No need to pay much attention to where it is when you remove it. When you're ready to close the hinge, pull down on the rod to take the...
-
JJimmyy reacted to OR VietVet's post in the thread There are just some days I wish I didn't turn wrenches with Like.
Yea, that yellow one is the "adjustment one". The top/cover flips up and the rod is serrated or threaded and can be moved to tighten or...
-
JJimmyy reacted to Fless's post in the thread There are just some days I wish I didn't turn wrenches with Like.
The rods aren't all that difficult -- except for getting that yellow hinged one to "open" to release the outside door pull linkage...
-
JJimmyy reacted to homesick's post in the thread There are just some days I wish I didn't turn wrenches with Like.
I agree. "Do the hard part first" is a basic wisdom. joe
-
JJimmyy reacted to OR VietVet's post in the thread There are just some days I wish I didn't turn wrenches with Like.
Yea, I been in the GMT800 doors a few times with no problems. Hers is just banged up from the hinge pins sag. First the pins, then the...
-
JJimmyy reacted to Fless's post in the thread There are just some days I wish I didn't turn wrenches with Like.
Driver's door latch isn't a bad job. After doing mine I had some slack when pulling the outside handle, but fixed that by adjusting the...
-
JJimmyy reacted to OR VietVet's post in the thread There are just some days I wish I didn't turn wrenches with Like.
The final special tool I need for the widow of an AL friend that passed, 2005 Tahoe driver's door hinge pins work, is here. Now I can...
-
JJimmyy reacted to Rocket Man's post in the thread Rocket Man's 2008 Bagged CC Silverado Build AKA "THE MACHINE" with Like.
Used the Cerakote headlight restoration kit and I am as impressed with it as I was with the trim kits. These were so hazy I almost...
-
JJimmyy reacted to ncalvo's post in the thread 2003 tahoe heater core, evaporator, blend doors, actuators with Like.
thanks for the help I did install a cabin air filter in my air box scouring the forum i seemed to find a post with a lot of helpful...
-
JJimmyy reacted to OR VietVet's post in the thread There are just some days I wish I didn't turn wrenches with Like.
It was supposed to rain, on and off today. It clouded up and she dropped at 11:30. I really thought it would be tomorrow before I...
-
JJimmyy reacted to OR VietVet's post in the thread There are just some days I wish I didn't turn wrenches with Like.
-
JJimmyy reacted to OR VietVet's post in the thread There are just some days I wish I didn't turn wrenches with Like.
-
JJimmyy reacted to mattbta's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Better view, one is angled and the other is straight. Should be a direct swap!
