I have had that happen on a previous chevy I had. For this suburban i got moog upper control arm bolts and cam plates to avoid that
only hardware I am reusing on the front is lower control arm bolts crossmember bolts, abs wire bracket and brake hose bracket bolts
Reinforced the forward upper control arm mount on the passenger side. the side that goes up to the strut mount is 1/8 inch that side I'm leaving alone but the rest of the control arm mount is 1/16 inch plate which had to much flex ability for my liking so welded a piece of 1/8 inch plate over...
Couple of questions.
The brake line bracket on the upper control arm mount that holds where hard line connects to the hoses. Can that be flipped to extend front brake lines down? There's two holes in mount one for bolt and one for a tab on the bracket. I will take a close up picture of that...
Front suspension out only took about 2 hours to get that far. But then ran into some troubles. trying to remove sway bar bushing bolts 2 of them stripped so gotta fix that. Cut first one gotta cut other one still and gotta get them out after that will have to weld nuts on them. And after...
I have read other threads asking exactly this and the welded plate gives a little extra strength but can be skipped most kits don't have it. If planning to wheel it hard I would get someone to weld it.
Finished the rear end and got it back on it's wheels front is up on blocks and rear suspension needs to settle. so it looks a bit taller than it will be. Wheel spacers made the tires are almost even with the fender flares but rear axle is about an inch off center toward the right because of the...
And the moog spring isolator pads that said they are for this generation suburban are alot smaller then the originals they fit kinda but not well so I gotta look into that if I can find better ones I will change them when I do rest of rear suspension
Yeah they are. I wanted lift knuckles to help cv angles with only dropping differential 1 inch and help tie rod angles. front lift is rough country 3.5 inch knuckle lift for 2007-2013 silverado sierra 1500s. They don't sell a knuckle lift for the tahoes and suburbans. Planning to use a truck...
Kinda layed stuff out and loosely mocked them up to see what everything looks like and how things fit together. control arms and tie rods are olive drab green not yellowish tan lol it looks kinda nice with all the black parts surprised how heavy some of these parts are. Also I have new brake...
The rear springs wheel bearings and outer tie rods came in today so that means I finally have almost all my parts. I only need wheel bearing bolts which will be here tomorrow :) excited to finally tear it apart and swap everything. theres a big pile of suburban parts in the dining room lol and...
4wd lift kits will work with a awd
but you will need to get a different front driveshaft with a double joint for it to work procomp and others sell them.
also make sure it's a quality lift that drops the differential proportionately with the lift hight and keeps cv axles at a relatively flat...
I ordered
rough country 11932 3.5IN GM SUSPENSION LIFT KNUCKLE KIT (07-13 1500 PU 4WD) with the n3 rear shocks and lift struts.
Skyjacker c25r rear springs
Mevotech tough terrain- outer tie rods, wheel bearings, upper and lower control arms with ball joints and sway bar links.
Stock replacement-...
I have not seen anything on spring rates. I wanted to know that too because I haul feed and building materials and pull a car trailer regularly. how do you plan to make them bolt? Would a plate over the top and bottom coil that bolts to spring pads work? I like that idea better than limit...
Let me know I will be ordering the same ones tomorrow and everything to completely rebuild my front and rough country lift struts to lift front 3.5 inches.
That's what I was thinking. We will see how they fit and lift it. I just don't want its rear to sag but don't want to much rake. lifting...
Has anyone here used skyjacker c25r or c50r rear lift coils in a 2007-14? They are made for the 2000-2006 suburban and tahoes. C25R lifts 2.5 inches c50r lifts 5 inch.
As far as I can tell the 2007-14s rear suspension is same as 2000-2006 and other replacement or heavy-duty springs are...
Summer has been busy. I have been doing 70-90 hours at work every week since end of may. Gotta love farming. so haven't had time to do much at home all my time off work is spent playing with the kids or sleeping lol. I did Get the 87s extra parts off and the z71 got completely stripped and a lot...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.