Search results

  1. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I shoulda rounded up some boards for under these engine hoist wheels. Lol
  2. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Fricken snow is really making me not wanna go crawl around under this thing today.
  3. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I didn't need to know about another upgrade, lol
  4. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I got fancy wire loom and tesa tape, so im gonna get the bay cleaned up a little after I get this yanked out. Probably put a pitman and idler arm in while they are easy to get to. I still need to paint a couple things like the coil brackets and steam tube. But it's been cold and if I paint in...
  5. Walchit

    Walchit's 2000 XL

    Progress!
  6. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Started tearing this thing out finally. And i didn't even round out the torque converter bolts, lol. Hoping to get it out tomorrow and get HP tuners ordered. Still have a few more things to buy, but I'm getting closer for sure
  7. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I built a growlight with LED strips, and I could tell they weren't gonna last, so I put dabs of superglue under them while I stuck them down. It's held for a few years now.
  8. Walchit

    My From Start to Finish 6.0L Build

    Love this thread! I need to get some stuff done on mine, been procrastinating
  9. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    What throttle body are you using? Did you just use the corvette filter to bypass the return?
  10. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    @Tonyrodz my line rusted out right above the rear end on the drivers side. I didn't see the leak until it was on the lift at the alignment shop the second time.
  11. Walchit

    ABS/ Brake light Question

    I had a bad wire on one of my wheel speed sensors. If your scanner will let you view live wheel speed data you could rule that out. Mine ended up being the module too though after I got the wheel speed sensor working. Mine will work until I hit a bump then the MILs come back on.
  12. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Ordered a rebuild kit for my injectors today. Might end up just running the gen3 intake, cause I don't really have money for a fuel pressure regulator and new throttle body.
  13. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    There were so many parts gone off of them it was hard to tell what they even were, lol. The newest on was placed like October 13th, so I was hoping maybe the intake was laying around. I thought about grabbing brakes and rotors, but then I would need new wheels.
  14. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I need to do at least the pitman and idler arms while I have the engine out. I should probably figure out a way to get a redhead too.
  15. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Drove up to the pick and pulls yesterday and really underestimated how much time I would need to find parts. The first one I went to didn't have anything, and was in line checking out at the second one until the 3rd one was closed. All of the nnbs trucks had the engines pulled already,but I...
  16. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    My buddy just wrecked his 900, and my second question may have been if he wanted to sell me the intake, lol
  17. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I wish mine was that clean!
  18. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    The oven cleaner seemed to work pretty good, I think I'm gonna call it good for now. I need to get this old engine the rest of the way out, I made some baggies with pieces of tape on them so I don't lose my nuts and bolts. I wish we had a pick and pull closer cause I would go look for the...
  19. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    15 minute soak in oven cleaner followed by the pressure washer got it looking pretty good.
  20. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I need to figure out how to get all of this carbon off the inside of the intake today.
  21. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    It depends on if you have the drive by cable or drive by wire. For drive by cable you need a chineese 92mm throttle body and a fuel pressure regulator, or I see some guys cramming a corvette filter on there. Lol Drive by wire needs this thing called an x-link, I heard people saying it was...
  22. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Been scrubbing, lol
  23. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I don't plan on drag racing this thing, and from my limited research it's the best cam for low rpm torque. I've been thinking about the dorman intake manifold, but I haven't been able to find any testing on it. Was looking at the ebay aluminum ones too, but I read that it will move the powerband...
  24. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Truck norris, it's pretty mild, but I'm pretty sure I read something about the 107 lsa possibly causing vacuum issues.
  25. Walchit

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I've been worried about losing vacuum with this cam, and thinking about converting to hydroboost.

Forum statistics

Threads
132,311
Posts
1,865,745
Members
96,901
Latest member
ToddYYC

Latest posts

Top