Search results

  1. gpracer1

    Weird steering problem fixed

    So your steering wheel position sensor was bad and you decided to just ditch / disable the system? Mine had the same problem, replaced the sensor on the steering shaft and back to normal.
  2. gpracer1

    Read diff question

    Well then that's what I'm doing when I do my rear disc conversion.
  3. gpracer1

    Need help with gas gauge problem!

    First you gotta qualify for the 120 mph with some mods :D :joke: Actually mine does over 120.
  4. gpracer1

    Need help with gas gauge problem!

    Had the same problem and it is the gauge itself......replaced with a used gauge cluster (Denali 120 mph) and its fixed.
  5. gpracer1

    Read diff question

    I'm going to have to invent a rear diff cover with a big oring.
  6. gpracer1

    G80 locking diff questions

    Get on a dirt road. Turn the steering wheel slightly. Punch it. If you start getting sideways, it's working. Plus you can back up and see the peel out marks in the dirt. I love the auto 4x4 button...... It will barely slip one rotation and go right into 4x4.
  7. gpracer1

    efan question

    Also get a smaller pulley for the alt. It will put out more at idle because the alt will be turning faster.....no more 11.5 volts at idle in gear.
  8. gpracer1

    1999 GMC Yukon problems

    Mine did the same thing, anything over 3K rpms and voltage would drop. New alt fixed it.
  9. gpracer1

    Transfer case fill plug location

    Fill plug location sucks the big one. After I did mine about a week later no more take off from the light clunk.
  10. gpracer1

    valve adjusting with new lifters

    I would submerse each lifter in oil and pump it up with a pushrod before install. I'm never adjusting valves again unless the engine is running and oil is actually flowing after my last time I thought they were pumped full of oil, but they weren't . I do 3/4 turn from zero lash right when it...
  11. gpracer1

    A/C problem

    Are you saying that while the compressor clutch is still on, the truck suddenly blows warm air? In that case either there is moisture or particles in the system clogging up the orifice tube, or the blend door is moving. You could always clamp down the heater hose inlet to stop hot water...
  12. gpracer1

    Scorpion 1.6 Roller Rockers Installed !

    Since jan I have been traveling for work 97% of the time, haven't even put my headers on yet.......hopefully soon , then dyno once it cools down from the 100's+
  13. gpracer1

    98 Yukon poor response...

    I assume you have a k&n type oiled air filter.......do NOT over oil it or you will foul up the MAF sensor.
  14. gpracer1

    Scorpion 1.6 Roller Rockers Installed !

    scp1036
  15. gpracer1

    Tahoe running like a bag of .........

    Did those punks put something in your tank?
  16. gpracer1

    Running Sluggish after Tune-up.

    190,000 for an O2 is waaaay too long.
  17. gpracer1

    Running Sluggish after Tune-up.

    Have you ever replaced the O2 sensor? If over 80K miles, replace it. How does it drive if you start it cold in the morning and immediately drive without warming up?
  18. gpracer1

    Rear door

    But I love sleeping with hoes..........l
  19. gpracer1

    Rear door

    Had both, hate the fact that on both types you can't open the doors or tailgate window from inside (back)......as in if you are camping or sleeping in back. I understand though that people's kiddies would be splatterd on the highway.
  20. gpracer1

    OBX Stainless Long Tube Headers, Doin It

    Think I paid about $350-400 to coat my vette headers, 6 foot long X pipe and 2 cats.
  21. gpracer1

    OBX Stainless Long Tube Headers, Doin It

    Well so much for the jet hot idea.....they used to be in Phoenix and I was gonna drop them off. Now it's $350 to coat them and $90 for shipping to Oklahoma :Stupid Me: I guess the prices went up since last time 5 years ago. I guess they are going in plain Jane .
  22. gpracer1

    anybody here with a jantszer ported throttle body installed.

    I have one. I don't remember how much later I got the tune, but I didn't have any codes or problems before or after. With the removal of the stock throttle blade damper, it flows much more air much sooner with very little throttle opening. I had the 0411 PCM when I installed the jantzer tb...
  23. gpracer1

    OBX Stainless Long Tube Headers, Doin It

    That's what most headers look like on the inside. I figure I have a tig and stainless is easy, so what the heck for that price.
  24. gpracer1

    OBX Stainless Long Tube Headers, Doin It

    iPhone pics...... 134556[/ATTACH]"] 134558[/ATTACH]"] 134560[/ATTACH]"] 134562[/ATTACH]"]
  25. gpracer1

    OBX Stainless Long Tube Headers, Doin It

    Just picked them up from UPS. I can't believe they were only $219 Hope to have this added to complete the mods and see 30-35 hp. This should make all the other mods work even better. [/IMG]

Forum statistics

Threads
132,314
Posts
1,865,820
Members
96,908
Latest member
Boosyed96GSX

Latest posts

Top