07 XL Denali

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Doubeleive

Wes
Supporting Member
Joined
Nov 7, 2017
Posts
26,206
Reaction score
39,274
Location
Stockton, Ca.
yea I understood. They were the first thing I checked, I'll check again though as I did not know about #2. I was referring to the fact that before nothing happened, now the self test at least was happening so I thought I was making progress lol.

There is no fuse 58. I'm looking for other fuses, I will check 2 and 54. Thank you. Already replaced 61 (Automatic level control compressor)
I looked up the ones for my 2012, so yours could be different looks like as noted 2/54/61, if you have not disconnected the battery ground I would do that as well because if all the fuses and relay is now good then it should make a good handshake with the module/bcm.
if that doesn't work then try scanning the whole system with the tech2 and see if it shows a issue with the level control module
 
OP
OP
C

carrmann

Member
Joined
Dec 16, 2022
Posts
86
Reaction score
106
oh ok gotcha. did all of the above. still can control exh valve, no compressor does not turn on other than for self test. I also tried raising/lowering the front and rear to see if it would trigger a adjustment (it didn't).

I did see a code for C0660 'level control exhaust valve circuit short to ground or open circuit'. last test and this ignition both say 'passed' however. I can control it to open/shut with the tech2 scanner and it works.

I'm going to grab another compressor and give that a go in case this new one is bad or wired wrong etc(I've read people getting them bad new out of the box).
 
OP
OP
C

carrmann

Member
Joined
Dec 16, 2022
Posts
86
Reaction score
106
Well, picked up a new unit (dorman). Doesn't work at all. No self test, exh valve and compressor don't do anything via tech 2.
 

Doubeleive

Wes
Supporting Member
Joined
Nov 7, 2017
Posts
26,206
Reaction score
39,274
Location
Stockton, Ca.
Well, picked up a new unit (dorman). Doesn't work at all. No self test, exh valve and compressor don't do anything via tech 2.
that's bizzare, i wonder if you just had bad luck and got 2 bad pumps in a row, does it work with a bench test?
 
OP
OP
C

carrmann

Member
Joined
Dec 16, 2022
Posts
86
Reaction score
106
that's bizzare, i wonder if you just had bad luck and got 2 bad pumps in a row, does it work with a bench test?
They both work with 12v applied directly

The original does not
 
Last edited:

Fless

Staff member
Super Moderator
Joined
Apr 2, 2017
Posts
11,856
Reaction score
24,114
Location
Elev 5,280
How much current do these pumps pull? Use a fairly heavy test light (like a turn signal bulb) to load the circuit (at the connector) to see if it can pass the current and light the light brightly. Might have a bad ground or a compromised wire.
 
OP
OP
C

carrmann

Member
Joined
Dec 16, 2022
Posts
86
Reaction score
106
ya, I don't know maybe check the the harness that connects to the pump and see if it has corrosion or is burnt or anything
connection at the pump looks close to perfect considering 168k miles.

I'm going to try and jump the relay in the next day or two, see if it will stay running while its jumpered so I know its at least not the power wires. Also going to check the chassis module/computer (whatever that is called) to see how it looks.
 
OP
OP
C

carrmann

Member
Joined
Dec 16, 2022
Posts
86
Reaction score
106
How much current do these pumps pull? Use a fairly heavy test light (like a turn signal bulb) to load the circuit (at the connector) to see if it can pass the current and light the light brightly. Might have a bad ground or a compromised wire.
No idea on the current. Thank you, I will try and give that a shot
 

Doubeleive

Wes
Supporting Member
Joined
Nov 7, 2017
Posts
26,206
Reaction score
39,274
Location
Stockton, Ca.
connection at the pump looks close to perfect considering 168k miles.

I'm going to try and jump the relay in the next day or two, see if it will stay running while its jumpered so I know its at least not the power wires. Also going to check the chassis module/computer (whatever that is called) to see how it looks.
there is a level control module also check that. it should be up under the frame in the rear, if you google a little you will see where it is located and what it looks like, should have a wide wire harness, triple row
should look just like this one
 

Forum statistics

Threads
132,311
Posts
1,865,742
Members
96,899
Latest member
mohd33303
Top