fleet model 4x4 questions

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

dojrs

Member
Joined
Jan 25, 2014
Posts
90
Reaction score
50
Hey y'all I'm new to this forum. I've been looking for a few items and can't seem to find them near me and have some technical questions also.
1)w here or who near south Georgia has a console from a escalade cheap?? Mine didn't come with one. I want both an overhead with the two lights and pocket and a floor console.
2) does anyone know if my fleet model came with keyless entry? ?
3) can I put electric power seats in it and them work properly ?? Want to put leather seats in it if I can find some decent affordable ones. CHEAP!!!
4) I've found a plug connector in my dash below my rear glass opener that was taped up from the factory has 4 or 5 wires in it. What was its purpose?
Thanks y'all for any help y'all can give me
 

SunlitComet

OBS Jedi-Do Good
Joined
Sep 30, 2010
Posts
16,206
Reaction score
188
Location
unknown at this time.
1. Not near you, but may need to add wiring if the provisions were not included in the build.

2. Not very likely if you have front sealed beams for headlights.

3. Again may need to add wiring, but otherwise will bolt in.

4. Possibly for a fog light switch that was never fully provisioned. I assume it is not the wiper switch which you likely have if you have a tailgate.
 

rmodel65

Full Access Member
Joined
Dec 21, 2013
Posts
102
Reaction score
0
there were a couple of esclades at the LKQ in savannah last time i was there what was left or not i dunno
 
OP
OP
D

dojrs

Member
Joined
Jan 25, 2014
Posts
90
Reaction score
50
Yeah the lights in the overhead I think I can do myself.
It doesn't have sealed beam head lights. They're the std ones not old school glass ones. Although trying to get them angled good for night driving is a pain the a$$
yes I have a tailgate model With the bare bones immenities. I would like to make it into a nicer interior because I like it as a whole for now. I played with the thought of a throttle body spacer and headers when I get the consoles any suggestions on throttle body spacer brand ? I only drive it about 70 miles per week so I was going with summit racing brand headers already has true dual exhaust on it. So I was gonna run the shortly headers.
 
Last edited:
OP
OP
D

dojrs

Member
Joined
Jan 25, 2014
Posts
90
Reaction score
50
there were a couple of esclades at the LKQ in savannah last time i was there what was left or not i dunno

How long ago was that ? I checked their website and It doesn't show anything not a tahoe, suburban, or anything I could use. And how easy are they to deal with? I've never been to a u pull it type place like that before. Im close to valdosta so I would probably go to the one in jaxville.

Here's a technical question for someone who has done this. How much work is it to put power seats in mine since it came as a fleet model? I know they will bolt in the same but what about the wiring ? Would I just have to run power and ground to the seat motor? I know these have been answered somewhere before but I haven't seen any posting about this.
 

rmodel65

Full Access Member
Joined
Dec 21, 2013
Posts
102
Reaction score
0
its been a couple of months since i was up there. i dont think they keep an inventory at the savannah LKQ there is also two halves to the business. one that you walk in off the street and pay either a dollar or two to get inside. and then you have the commercial side where they dismantle the cars and sell the parts to dealerships etc at a higher cost
 

SunlitComet

OBS Jedi-Do Good
Joined
Sep 30, 2010
Posts
16,206
Reaction score
188
Location
unknown at this time.
How long ago was that ? I checked their website and It doesn't show anything not a tahoe, suburban, or anything I could use. And how easy are they to deal with? I've never been to a u pull it type place like that before. Im close to valdosta so I would probably go to the one in jaxville.

Here's a technical question for someone who has done this. How much work is it to put power seats in mine since it came as a fleet model? I know they will bolt in the same but what about the wiring ? Would I just have to run power and ground to the seat motor? I know these have been answered somewhere before but I haven't seen any posting about this.

Just power and ground, but run the power through a 30 amp circuit breaker and not a fuse.
 

Forum statistics

Threads
133,248
Posts
1,882,112
Members
98,284
Latest member
cofferson
Top