clandr1
Latest activity Postings About
-
-
clandr1 reacted to 5x10's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with
Like.
Gave it a bath and replaced the old crusty tail lights -
clandr1 reacted to nonickatall's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Painted my rear wiper..
-
clandr1 reacted to Kman's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Had new Michelin Defender LTX tires installed on my 2001 Tahoe LT. Almost at 219k miles.
-
clandr1 reacted to Fless's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Took 'er into my local shop for some work I can't do. Oil pan gasket & o-ring, parking brake cables, diff axle seals, and a few other...
-
clandr1 reacted to mattbta's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Put these on - took about an hour lollygagging in no particular rush. The originals show no visual signs of being bad and passed the...
-
clandr1 reacted to SilverSport's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Love.
2024 GMC take off wheels and tires added...20 inch with 275/60/20 Continental LX-20s...
-
clandr1 reacted to treehan77's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Love.
After 2 fails apiece at the GMC dealer and Chevy dealer and them first claiming it wa good to go, then blaming my new tires (I also...
-
clandr1 reacted to 5x10's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Ac blower motor starting knocking after I replaced a failed resistor bought new resistor and fan, oem spliced into wires as I read a...
-
clandr1 reacted to mattbta's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Took it for a balance/rotate, alignment, and new spare. That thing is original (2004) and only used once in 2006. Don't want to get...
-
clandr1 reacted to mountie's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
I replaced a Northstar V8 in my '93 Cadillac STS ...... I cleaned, and MORE IMPORTANT, I heat-shielded as many fluid lines & wire...
-
clandr1 reacted to ZEUS1's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Wow.
Got my motor out, now i got to clean everything up before i stuff the new one back in.
-
clandr1 reacted to mwilson62000's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Swapped to an Escalade gauge face.
-
clandr1 reacted to latvius's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
Yeah it is not even close to fitting. The Denali cup holders are much smaller than the Tahoe.
-
clandr1 reacted to mjgirard's post in the thread What did you do to your NBS GMT800 Tahoe/Yukon Today? with Like.
I drove from Virginia Beach, VA to Ashland, VA to meet my daughter for her birthday lunch. Round trip around 230 miles, lots of traffic...
-
clandr1 replied to the thread What did you do to your NBS GMT800 Tahoe/Yukon Today?.Did you try fitting it in your Denali with the cutouts facing towards the front of the truck? It is offset a bit to one side (I...
-
-
Loading…
-
Loading…
