Recent content by aflumb
-
Belltech 8mm spacer
Well after moving 3x in 3 years I have apparently lost all the spacers for my front struts and of course there no longer available separately. So does anyone have any sitting around they would like to get rid of Just installed DJM arms and need them badly- aflumb
- Thread
- Replies: 1
- Forum: Street Suspension
-
Suspension Re-vist
well after installing both new front bell tech shocks and the new steering rack bushing. the truck drives amazing now.- aflumb
- Post #4
- Forum: Street Suspension
-
Suspension Re-vist
Well after crawling around under the front end. found that the pass/front shock is leaking and the bushing for the steering rack is shot. so alls on order and should be in this week. hopefully this will fix the steering wheel shake im chasing- aflumb
- Post #3
- Forum: Street Suspension
-
What did you do to your NNBS GMT900 Tahoe/Yukon Today?
Been a pretty expensive week for the ol Wifey wagon Replaced the following: - Front Driver door panel (got tired of the broken grab handle) - brake pads, rotors, front brake lines - Flushed the brake fluid - rear wheel bearings - right rear wheel speed sensor - right rear brake caliper - rear...- aflumb
- Post #39,458
- Forum: General Discussion
-
Suspension Re-vist
So after having Nor Cal SS's 3-5 kit on the wife's 2012 Tahoe (rear is TBSS air shock, the Bell Tech rear springs are garbage) for about 75K miles/8 years. The Tahoe only has 96K miles. With that said I have been chasing a really bad shake after hit any kinda bump in the road. Tires/wheels just...- aflumb
- Thread
- Replies: 3
- Forum: Street Suspension
-
NNBS hitch cover (close out)
Looking to see if anyone has the factory hitch cover/close they wanna sell. Color doesn’t matter. -
4 Piston Big Brake Upgrade from 2019-20
I'm going to PM you- aflumb
- Post #587
- Forum: Engine & Drivetrain
-
4 Piston Big Brake Upgrade from 2019-20
Do you still have any ava?- aflumb
- Post #585
- Forum: Engine & Drivetrain
-
Testing the waters
well my 12 is running the replacement TBSS bags and an airlift compressor system (https://www.amazon.com/LIFT-25804-Air-Shock-Controller/dp/B000CFO05E/ref=sr_1_4?crid=2QCFVJAJJ9RT4&keywords=airlift+compressor+kit&qid=1644179043&sprefix=airlift%2Caps%2C253&sr=8-4) . pretty simple really bags spun...- aflumb
- Post #2
- Forum: Street Suspension
-
power fold mirror question/now heated seats do not work
So earlier this year I installed power folding mirrors in the wires tahoe. I had the switch from a truck that had them from the factory. Question I have is, now that they are installed the heated seats don't work? all the fuses check out. its as if something needs to be programmed . any insight... -
What did you do to your NNBS GMT900 Tahoe/Yukon Today?
before I moved to VA last year I had a house up my the Aliente Hotel.. but since this move is temp unless I find a job worth staying there we will be renting somewhere out that direction. or really up off west Flamingo.- aflumb
- Post #36,056
- Forum: General Discussion
-
What did you do to your NNBS GMT900 Tahoe/Yukon Today?
Well in preparation for the move back to Vegas the Wifey Wagon got a little bit of work - oil/filter change - power steering fluid flush - greased the whole truck - cabin air filter - full interior detail - washed and a new coat of wax over the ceramic coat - and ordered a new set of rims for...- aflumb
- Post #35,984
- Forum: General Discussion
-
What did you do to your NNBS GMT900 Tahoe/Yukon Today?
man this is good to know. I was talking about trying to figure out away to do this and you just made my day. I use my AMEX as basically my debit card and pay my bills with it. Hopefully this will help them and they will be better off than I was- aflumb
- Post #33,147
- Forum: General Discussion
-
What did you do to your NNBS GMT900 Tahoe/Yukon Today?
It’s an issues if there not stainless. Will they rust? Yes. But am I concerned no. For the cost to coat them I can by another set in the xx years it’s going to take to rust. The wrap works amazing ( 2nd vehicle I have wrapped the manifold) for my purpose and need. And the cost. If I had a set...- aflumb
- Post #33,127
- Forum: General Discussion
-
What did you do to your NNBS GMT900 Tahoe/Yukon Today?
Well after putting it off for awhile I finally got tired of adding parts to my cart and not going thru with it. First delivery. Had to get the Autocal since I didn't when they did unperson tune Second shipment. Speed engineering 1 7/8 headers/ and y-pipe installed. wasn't to bad. if you...- aflumb
- Post #33,125
- Forum: General Discussion
