Front end Rebuild

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Pressureangle

Member
Joined
Aug 6, 2024
Posts
34
Reaction score
33
Hey yall. I have a 02 suburban with 200k miles.

It has all the original steering and suspension components. Which are all worn which makes steering the thing a chore.

Money is tight right now so I need some budget but decent parts that will hopefully last me for the next year to year and a half.

What would you guys recommend? It's bone stock ride height, no modifications there.

Any of y'all have any experience with SKP or any other suspension brands from RockAuto that I can get a solid year out of?

Thanks!
I've always been surprised at the quality of parts from Detroit Axle. Their warranties are usually way better than others'.

 
OP
OP
JPVortex

JPVortex

Full Access Member
Joined
Jan 13, 2022
Posts
278
Reaction score
207
Location
Connecticut
Ok thanks guys! How do I make sure it’s not backward/upside down? Anyone got a picture of proper orientation for it?
 
OP
OP
JPVortex

JPVortex

Full Access Member
Joined
Jan 13, 2022
Posts
278
Reaction score
207
Location
Connecticut
I've always been surprised at the quality of parts from Detroit Axle. Their warranties are usually way better than others'.

I’ve seen extremely mixed reviews for Detroit Axle. I did look at one of their front end kits on Amazon. However, I got scared away. There was multiple people who had ball joints separate on them. That’s serious life or death stuff.
 

latvius

Full Access Member
Joined
Nov 17, 2014
Posts
424
Reaction score
587
Location
Ariton Alabama
Topside of the drawing shows installed wrong. Even with pictures it can be a head scratcher. The holes where the pitman arm and the other end (endlink?) are cone shaped so you can only install it in that respect one way.

20240811_150552 (1).jpg
 
OP
OP
JPVortex

JPVortex

Full Access Member
Joined
Jan 13, 2022
Posts
278
Reaction score
207
Location
Connecticut
Topside of the drawing shows installed wrong. Even with pictures it can be a head scratcher. The holes where the pitman arm and the other end (endlink?) are cone shaped so you can only install it in that respect one way.

View attachment 440502
Thank you very much! Should be pretty easy to not mess that up.

Cant I also go by the grease zerk position for the inner tie rods? Arent they supposed to be facing down?
 

latvius

Full Access Member
Joined
Nov 17, 2014
Posts
424
Reaction score
587
Location
Ariton Alabama
Thank you very much! Should be pretty easy to not mess that up.

Cant I also go by the grease zerk position for the inner tie rods? Arent they supposed to be facing down?
They will still be down, the way I could envision it is I took an offset wrench and held it sideways covering one end with may hand. Take that wrench and swivel it 180 degrees left and right.
 
OP
OP
JPVortex

JPVortex

Full Access Member
Joined
Jan 13, 2022
Posts
278
Reaction score
207
Location
Connecticut
They will still be down, the way I could envision it is I took an offset wrench and held it sideways covering one end with may hand. Take that wrench and swivel it 180 degrees left and right.
3E0E7DAA-B6EE-463D-A159-F28AFF4DD4EC.jpeg
So basically it’d go like this?
 
OP
OP
JPVortex

JPVortex

Full Access Member
Joined
Jan 13, 2022
Posts
278
Reaction score
207
Location
Connecticut
So just to make sure I'm making sense of this here. I drew out my own diagram. This diagram I drew is as if Im UNDER the truck.

The way I think about it, basically I want the curved parts on both sides(where the tie rods eventually connect) to be facing toward the REAR of the vehicle.

If I were to turn it 180 degrees the curved parts of the center link would be facing the FRONT of the truck, which would be the INCORRECT way.

Am I correct here?

1729043954506.png
 

Forum statistics

Threads
132,038
Posts
1,861,383
Members
96,487
Latest member
ericjvasil69
Top