To be clear there is a lead from the camera housing about 18 inches long maybe. then this part number will get you from the lead to the line for the rear wiper washer. If you watch the videos I think I talk about how I got the lead from a used assembly off ebay.
I just found some clips on amazon but they weren't perfect replacements. I did try to separate the connectors but I couldn't tell that I could do it without breaking something. I may go back and look at it again. I still have all the stuff I didn't use.
Ideally someone could reprogram the computer to accept the lower voltage of the LED's and they would be plug and play but to my knowledge the new electrical architecture is encrypted and there has been very limited success in being able to do that. I haven't looked in a while but I think I've...
What size resistor did you use? That could be why you needed two. I tested one on each side and it was too much. There is a video on YouTube of a guy placing resistors behind the tail lamps but they looked smaller than the ones I tested.
Since the reverse bulbs are both on the same circuit that could be done with a single jumper and single resistor installed on either side. I would think they would make that for you at a lower price.
Those are the connectors and I have a guess on the 2 pin but I'm not 100%. The Yukons have brake lights that extended into the liftgate. I believe the 2 pin may be where the wiring to trigger those brake lights connect but it's only a guess. I have the empty 2 pin as well.
I would just call the number on the website. I don't know what the holdup is on getting the listing on the site. He's told me multiple times he would have it up in a few days and so far he hasn't gotten it up there yet. But he did tell me he's already sold a set to somebody else based on them...
I don't remember how long it was in reverse but the Yukon lights are full LED. The issue is programming. The Yukons are meant to have LED so the computer looks for appropriate voltages. The Tahoe's are meant to have incandescent bulbs so the computer looks for that appropriate voltage. The ideal...
I can't remember where I found it but I believe operating temperature on these resistors is up to 315 degrees. The heat of the resistors was the whole point of the idea to locate them under the bumper. The 230 degree reading was with the vehicle sitting in reverse with the parking brake set so...
I have not had a single error since installation. I was told the listing would be up on the site today but if you don't want to wait any longer send them an email or call the number on the site. He told me he had already had someone reach out and he had sold a set. Hopefully it's listed by the...
Still waiting on the listing to be posted on the site for the harnesses but I just installed this Canvasback Cargo Liner if anyone is interested in checking it out.
Here is the response I got from Diode Dynamics. Honestly I think the cost of the bulbs gets you free shipping anyway but they do say they have a sale coming up and provided a free shipping code...
"Thank you for reaching out and sending that video! Unfortunately, due to our MRP policy with our...
I'm going to go ahead and give y'all the full install video. I'm not sure what the delay is on getting the product on the site. Hopefully its out soon so you are able to order.
No guarantees but I have reached out to Diode Dynamics to see if they would offer some discount if you purchased the...
The way I understand it the wattage is the amount of heat the resistor can handle before it begins to fail and in the case of our turn signals start hyperflashing. Lasfit offers a bulb that has a built in resistor but they warn if it's left on too long it will over heat and begin to hyperflash...
Brake and Turn Signals are separate circuits on each side. The reverse lights are a single circuit which is why you only need three resistors on one side and two on the other. It doesn't matter which harness goes on which side. Sorry for the delay but I'm still waiting for them to get the...
Sorry guys. I'm waiting on the website to get the listing up. I can say I went on a road trip Wednesday from Eastern North Carolina to Busch Gardens in Williamsburg VA and I didn't get a single error, warning, or issue regarding the lights. It's about 3 hours one way.
These are new harnesses that will be available soon at Gen5diy.com. I've provided them with an install video and they will have them listed for sale soon. I'm not aware anyone else offers these. I've seen people tap resistors in behind the tail lamps but I've measured temperatures on these...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.