Search results

  1. Knope

    02Yukon to Denali

    I almost forgot to mention the stainless steel brake lines. I was mainly focusing on the ride to see if it was any smoother when I was coming up to a stop light and had to stop more quickly than usual. It was a noticeable difference and a nice surprise. Overall, I'd say the 07+ upgrade is...
  2. Knope

    02Yukon to Denali

    285/50/20 Our ride heights have never matched up when comparing components.
  3. Knope

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I've thought about that as well. It's probably the rear belltech springs. I knew that if I changed the rear, I'd have to change the spindles. By doing the front first, I can get a feel for how the front and rear impact the ride separately instead of as the whole package.
  4. Knope

    02Yukon to Denali

    This is a shot with stock spindles back on. Measurements 34-1/2 front and 35 rear
  5. Knope

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Riding and handling good are subjective. It has been a bit rough for me over the past few months and I often have 2+ people riding with me since I have the largest vehicle of all my friends. That being said, we have a trip to Gatlinburg coming up and last year it scrubbed and jarred us to...
  6. Knope

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    It was just too low for the look I was going for. I actually rode around with the torsion bars turned up for the past month or two. If I'd have gotten 22s to start with, it'd be a good fit. 20s with A/T tires look better with a slightly higher ride height.
  7. Knope

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Back to stock front spindles. Swapped out belltech sp drop shocks for Bilstein 4600 in the rear. Alignment and tire rotation. Stainless front brake lines
  8. Knope

    My custom/stock wheels

    I think the stock look is a great classic look for that vehicle. The new rims look amazing though. The amount of creativity and craftsmanship put into them is mind boggling. Well done!
  9. Knope

    Show me your tail lights

    A little late to the party, but I think these look really good and don't cost much (<$110). They do require resistors, though.
  10. Knope

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Where would the seat ground?
  11. Knope

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    yep
  12. Knope

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Yep, both worked before.
  13. Knope

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    No luck after either. I must've missed a connection or something because it has to be highly unlikely that both were working before and aren't now.
  14. Knope

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Thanks. I just disconnected the battery to see if that'll help. Gonna wait a few then try it again.
  15. Knope

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Finally got the leather seat covers replaced and installed in the truck. Neither of the power seats are working though. Everything is connected, so I'm not sure what has happened. Any suggestions?
  16. Knope

    02Yukon to Denali

    I had to change to the park/signal lights for the new grill, but the actual headlights are stock.
  17. Knope

    02Yukon to Denali

    I got it from Amazon for less than $20. I very rarely listen to FM stations, but I took the stock antenna off months ago and just wanted something small to replace it. As for reception, I can't really comment since I only listened long enough to make sure it was picking up a station, but it...
  18. Knope

    02Yukon to Denali

    You were right about them being regular Yukon lights. My truck isn't a Denali, but I've completed the front end conversion.
  19. Knope

    02Yukon to Denali

    Other than looking hazed over, nothing happened. I've got a set of black housing depo projectors sitting in the garage ready to be installed. After viewing your build thread, I think they're the same ones you have.
  20. Knope

    02Yukon to Denali

    In order to get around after the hurricane, I had to put the seats back in the truck. I added the picture of the passenger seat installed in the previous post. The driver side foam cushion still hasn't arrived, but I had to put the seat back in with the old cover barely attached. It's only...
  21. Knope

    02Yukon to Denali

    Before PS: getting the bolt holes to line up on the power seat controls was a little bit of a pain.
  22. Knope

    02Yukon to Denali

    Haven't installed the stainless lines yet, but I'm planning on putting this new cover on the driver seat tomorrow.
  23. Knope

    04 Yukon, Bought not Built

    Good looking trucks.
  24. Knope

    02Yukon to Denali

    And on a separate note, I'm going back to the stock spindles in front. It's just too rough and looks lower now than it did before. Hopefully turning the torsion bar bolts down can keep it level.
  25. Knope

    02Yukon to Denali

    The new rotors, calipers, and pads made a difference. I can tell the truck stops more quickly, however I want a little more bite on the initial stopping power. I'll be adding the stainless flex lines next to see the additional improvement they add. I'll report again once stainless lines are...

Forum statistics

Threads
133,743
Posts
1,890,288
Members
99,012
Latest member
carloogbuyNuh

Latest posts

Top