Search results

  1. alaska_guy

    Programming mileage in a replacement cluster

    I'm in Palmer, AK.
  2. alaska_guy

    Heated seat thermistor bypass?

    The junkyard in Chugiak let's you do u pull its. I did it all the time.
  3. alaska_guy

    Update to adding trans temp gauge...

    Hp tuners will allow you to fix the axle ratio and brake booster message. If I had my suburban still I would of been able to tell you what two wires to tie together to get rid of that message. It's looking for a normally closed circuit.
  4. alaska_guy

    2004 Yukon Dash Light Issue

    Cluster needs to be rebuilt if your not getting odometer, PRNDL. Etc. Not sure on your radio. The circuit controlling those is your accessory switched 12v wire.
  5. alaska_guy

    Programming mileage in a replacement cluster

    Multiple ways to do it... to bad your too far away. I only charge $40 to reprogram mileage.
  6. alaska_guy

    Key and Key Fob Replacement Guide

    Does this same procedure work on 03-06?? I would like another fob
  7. alaska_guy

    Tool to disable tpms all together

    It's not the light. It's the one that says "service tires" or whatever on the odometer display
  8. alaska_guy

    Tool to disable tpms all together

    I took the escalade to a few shops a few years ago, had new sensors put in, had them try and pair etc etc. Both shops said well sometimes they just don't pair properly and it's something with your vehicle. Long story short, what tool can I buy to delete the tpms message on the cluster.
  9. alaska_guy

    Update to adding trans temp gauge...

    You can remove the brake booster message by shorting the two outer pins on the connector. I did this on my suburban.
  10. alaska_guy

    Wife's escalade taking a while for heat.

    I back flushed the heater core as I said I was going to do. That fixed the issue.
  11. alaska_guy

    Wife's escalade taking a while for heat.

    Working nice and hot now.
  12. alaska_guy

    Wife's escalade taking a while for heat.

    Ok, not the thermostat. Another issue I haven't spent time to fix. Obd port no longer works. Crawled under and no wires disconnected grounded etc I could see. So I can't scan with my reader. Common issue for blend motor? I know of Silverado there is some resistor pack deal on the passenger...
  13. alaska_guy

    2006 gmc yukon xl slt plus gauge cluster.

    Yeah, more than likely he just doesn't like programming them. I rebuild clusters locally and easiest way is to buy new eproms, flash them with trans motor settings and then place the new chip on your cluster. At least that's how I do it. It's not hard, but takes time. Where about are you...
  14. alaska_guy

    Wife's escalade taking a while for heat.

    Vehicle only has 130k moles on it. We are the second owner purchased with 98k miles. Had the entire thing gone through by the dealer when we bought it and have had numerous spot checks along the way as we get the oil changed. Radiator looks fine. I will replace the tstat as that's an easy...
  15. alaska_guy

    Wife's escalade taking a while for heat.

    Coolant level is fine. I had the blend motors fixed initially when I bought the vehicle as it would only blow cool air in the rear. The heat eventually works, scan tool and gauges match for coolant temp. I have a laptop to datalog real time. So replace thermostat first and then look at blend...
  16. alaska_guy

    Wife's escalade taking a while for heat.

    Guage will show 210 on the temp Guage but no heat until a few minutes after... seems it's slowly gotten worse. Used to heat up quick. Any idea?
  17. alaska_guy

    Very very dim LCD screen

    He has an 02, totally different fix.
  18. alaska_guy

    Now what?

    This year I believe still used a throttle cable. You more than likely have a bad/dirty IAC. If your vehicle is drive by wire, disregard.
  19. alaska_guy

    Change the color of your 00-02 Tahoe/Yukon AC control backlights with LEDs

    You can run jumper wires using some copper wires. Not exactly sure what you have going on, but just use some solder and a copper wire and jump it over to the good trace.
  20. alaska_guy

    Voltage meter

    Just make sure when you get a 2005 model, you get one that matches your vehicle. I do cluster repairs all the time so if you need help just PM me. Steering wheel model clusters are different than base models. IE: If you get a base model it wont allow your steering controls for gas and all the...
  21. alaska_guy

    Interior mod ideas?

    Yukon Center Console is pretty nice. I own an escalade and prefer the Yukon look. Here is my custom instrument cluster. I also put blue leds in all my dash stuff... HVAC, Headlight, rear wiper, 4x4 switches etc.
  22. alaska_guy

    Voltage meter

    My money is on that's an 03-04 cluster in an 05 truck. I just had to remove the light for someone this past week with the same symptom.
  23. alaska_guy

    Steering wheel buttons LED's.

    It's too cold to mess with my steering wheel stuff here in AK outside. I really don't want to cut a junkyard harness out... Scotty?
  24. alaska_guy

    Steering wheel buttons LED's.

    Anyone have a pinout or diagram so I can bench test my steering wheel buttons? I want to verify polarity is correct etc. They are all put back together.
  25. alaska_guy

    What is low miles for a 2006 Yukon Denali?

    It just gets fluid and filter for the trans. No flushing! I also use VP Racing products.

Forum statistics

Threads
132,818
Posts
1,874,783
Members
97,678
Latest member
Welch2324

Latest posts

Top