2007 Tahoe Power Lift Gate not working

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Trailblazzin

Full Access Member
Joined
May 29, 2017
Posts
169
Reaction score
77
Location
Lancaster PA
My power lift-gate is no longer operational. The only way to open it is to hit the button and manually pull it open. But to do that i can only open about 3-4” and then required to pull through some resistance and then a pop that allows it to open.

I have these DTC from the lift gate module.
B153E 08
B153A 08
B396A 02
B153B 02

I cleared the codes and tried to open it with my Tech2 and get the same results. This time i got the below codes.

B1019 00
B153E 08
B153A 08

Any ideas on a fix let me know. Thanks!
 

BG1988

Full Access Member
Joined
Nov 14, 2018
Posts
2,967
Reaction score
1,350
153E Description The liftgate control module continuously monitors power liftgate operation and calculates its location and direction of travel using 2 Hall effect sensors that are part of the liftgate
 

wsteele

Full Access Member
Joined
Dec 26, 2020
Posts
1,731
Reaction score
2,351
My power lift-gate is no longer operational. The only way to open it is to hit the button and manually pull it open. But to do that i can only open about 3-4” and then required to pull through some resistance and then a pop that allows it to open.

I have these DTC from the lift gate module.
B153E 08
B153A 08
B396A 02
B153B 02

I cleared the codes and tried to open it with my Tech2 and get the same results. This time i got the below codes.

B1019 00
B153E 08
B153A 08

Any ideas on a fix let me know. Thanks!

Have you turned off the power lift gate on the center console switch (put it in manual mode). When you do that will it open and close normally (manually)?
 

wsteele

Full Access Member
Joined
Dec 26, 2020
Posts
1,731
Reaction score
2,351
On the codes, just cut and pasted from the shop manual:

B153A
Liftgate Latch Switch Signal Circuit
LGCM
DTC B153A

B153B
Liftgate Open Switch Signal Circuit
LGCM
DTC B153B

B153E
Liftgate Position Sensor Signal Circuit
LGCM
DTC B153E

B396A
Liftgate Motor Control Circuit
LGCM
DTC B396A

B1019
System Configuration Error
LGCM
DTC B1019
SDM
DTC B1019
 

Attachments

  • 1623589285239.png
    1623589285239.png
    170 bytes · Views: 12
  • 1623589285397.png
    1623589285397.png
    170 bytes · Views: 11
  • 1623589285338.png
    1623589285338.png
    308 bytes · Views: 10
  • 1623589285515.png
    1623589285515.png
    321 bytes · Views: 9
  • 1623589285364.png
    1623589285364.png
    321 bytes · Views: 8
  • 1623589285423.png
    1623589285423.png
    283 bytes · Views: 5
  • 1623589285305.png
    1623589285305.png
    314 bytes · Views: 4
  • 1623589285267.png
    1623589285267.png
    283 bytes · Views: 4
  • 1623589285488.png
    1623589285488.png
    308 bytes · Views: 3
  • 1623589285456.png
    1623589285456.png
    314 bytes · Views: 9

Just Fishing

Can't fix stupid
Joined
Aug 30, 2020
Posts
3,988
Reaction score
8,672
Location
Utah
Looking in the factory service manual, skimming over those codes.
I see that a bunch of them show up as "Short to ground"

Might not hurt to check over the wiring harness.
if you happen to have a tech2, it might be handy to go through the special functions of the lift gate and manually activate each one to possibly narrow down where the issue is.

For my liftgate, just dicking around with the tech2.
I found out where the installer pulled power for the aftermarket backup camera.
The Liftgate! :jester:
 

Just Fishing

Can't fix stupid
Joined
Aug 30, 2020
Posts
3,988
Reaction score
8,672
Location
Utah
I hope you can read this, I have to reduce the size of the image.

1623865199394.png
 

Forum statistics

Threads
132,730
Posts
1,873,324
Members
97,563
Latest member
bmead21
Top