2015 Yukon XL Factory Air ride suspension diagnosis question

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Boatguy1x

TYF Newbie
Joined
Oct 29, 2024
Posts
2
Reaction score
1
2015 GMC Yukon Xl SLT 4x4. Standard air leveling shocks(not magnaride) Compressor was running quite long after start up. Found a leak in the shocks, so I replaced both sides with AC Delco #19432783. Everything was fine for a couple of weeks. Then I noticed compressor running every morning at start up. Started checking and found shocks deflated every morning. I checked for leaks and couldn't find any.
When I finally got around to try and diagnose, they don't even inflate now and the compressor doesn't run.
After reading some forum discussion, I did a couple of things.
1) Jumped terminal 30 and 87 and the compressor did not run.
2) Saw a diagnosis YouTube video on the compressor that powered the red and black big wires directly from a 12v source. I did this and the compressor did not run.
I have a limited function scanner and it indicates a C0712-00 Code - Level Control Compressor Relay Circuit

I have a new relay inbound to try, but I am wondering if the code is leading me astray and it might be the compressor itself?
Any other steps to help isolate?
 

wjburken

Supporting Member
Joined
Dec 26, 2017
Posts
9,950
Reaction score
27,523
Location
Eastern Iowa
My guess is you have a burnt up compressor. This can be caused by leaks in the system or a pressure relief valve that doesn’t close all the way.

Can’t speak specifically to the 2015 year, but have had to swap out more than a few on my generation of vehicles.
 

Doubeleive

Wes
Supporting Member
Joined
Nov 7, 2017
Posts
26,204
Reaction score
39,271
Location
Stockton, Ca.
2015 GMC Yukon Xl SLT 4x4. Standard air leveling shocks(not magnaride) Compressor was running quite long after start up. Found a leak in the shocks, so I replaced both sides with AC Delco #19432783. Everything was fine for a couple of weeks. Then I noticed compressor running every morning at start up. Started checking and found shocks deflated every morning. I checked for leaks and couldn't find any.
When I finally got around to try and diagnose, they don't even inflate now and the compressor doesn't run.
After reading some forum discussion, I did a couple of things.
1) Jumped terminal 30 and 87 and the compressor did not run.
2) Saw a diagnosis YouTube video on the compressor that powered the red and black big wires directly from a 12v source. I did this and the compressor did not run.
I have a limited function scanner and it indicates a C0712-00 Code - Level Control Compressor Relay Circuit

I have a new relay inbound to try, but I am wondering if the code is leading me astray and it might be the compressor itself?
Any other steps to help isolate?
could be, they fail just as much as the shocks do, I recommend the dorman pump, I had issue's with the arnott pump
 
OP
OP
B

Boatguy1x

TYF Newbie
Joined
Oct 29, 2024
Posts
2
Reaction score
1
My guess is you have a burnt up compressor. This can be caused by leaks in the system or a pressure relief valve that doesn’t close all the way.

Can’t speak specifically to the 2015 year, but have had to swap out more than a few on my generation of vehicles.
I was kind of wondering if maybe it was the valve that might be the culprit.
 

Doubeleive

Wes
Supporting Member
Joined
Nov 7, 2017
Posts
26,204
Reaction score
39,271
Location
Stockton, Ca.
I was kind of wondering if maybe it was the valve that might be the culprit.
if the relay gets the pump going again, you can spray it with a soap & water mix and check for bubbles, that was one the issue's I had with the arnott pump, relief valve was leaking
 

Forum statistics

Threads
132,301
Posts
1,865,642
Members
96,885
Latest member
BinOdhaib
Top