Muffler only replacement

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

brotten

Member
Joined
Jan 12, 2014
Posts
69
Reaction score
22
Location
Kansas City
I'm considering a muffler swap on my 05 Hoe. I want to replace the muffler with something I can clamp in and have some growl. Looking at a Walker Exhaust 17809 or simular. Does anyone have any suggestions or similar set up?
 
Last edited:
OP
OP
brotten

brotten

Member
Joined
Jan 12, 2014
Posts
69
Reaction score
22
Location
Kansas City
I'm looking for something that will be easier to bolt on. I need to get under the truck and measure the factory muffler.

Sent from my SM-N900V using Tapatalk
 

YukonXL04

The Riverboat
Supporting Member
Joined
Sep 3, 2013
Posts
2,489
Reaction score
175
Location
Arlington, TX
Yeah you need to measure the muffler and buy one the same length. However why not just buy one and have a muffler shop weld it in?
 

01ssreda4

Full Access Member
Joined
Feb 28, 2014
Posts
1,124
Reaction score
487
Stupid trying to pick a muffler that will bolt in? Why is it stupid? Because the chances of that happening are slim to none. Get one that is sorta close, and have a muffler shop take care of it. Hardly any muffler is going to "bolt in".
 

Moose912

Full Access Member
Joined
Mar 16, 2014
Posts
121
Reaction score
33
Location
Indy
i have always used a flowmaster "knockoff". half the price, good sound, and a nice little oomph in the seat. nothing crazy, but between an intake mod and exhaust, it helps. check a local shop, preferably a guy who does it on his own. most franchises are limited on what they can do and what brands they sell. also, youtube some videos and see what sound youre looking for. ive had "a**hole" loud and "barely louder than stock with a groan for looks" loud. no matter what, make sure to check out options and listen before you purchase! it sucks spending money and then having to spend more next week!
 

Chiggy

Full Access Member
Joined
Nov 7, 2013
Posts
144
Reaction score
2
Location
Kansas City, MO
You'll need to take it to a pro and they are going to have to do some cutting and welding unless you get a "cat-back kit". The stock muffler is a single inlet, dual outlet that Y's back together right behind the muffler. When the guy (my friend that owns a muffler shop) cut mine off and I looked at it I was baffled. Truly a stupid design. My friend put a short piece of pipe, the magnaflow stainless steel muffler in place and bent a small piece to connect to the stock tailpipe. It sounds amazing. Nice and quiet when cruising down the highway, nice and deep and loud when I stomp on it.
 

Zumwalt

Member
Joined
May 3, 2014
Posts
44
Reaction score
1
Location
El Paso, TX
I went through so many youtube vids for the right sound I want, found that Thrush Glasspack 3" in/out 24242 $32.99, im gonna have a shop weld it in place, ill do a before after vid post to youtube and post here to see what ya think.
 

YukonXL04

The Riverboat
Supporting Member
Joined
Sep 3, 2013
Posts
2,489
Reaction score
175
Location
Arlington, TX
My muffler shop did the same with my borla. $60 with welding the tip on Too.
 

Forum statistics

Threads
132,723
Posts
1,873,189
Members
97,553
Latest member
AceDawg
Top