Maybe reach out to the mfg to see if there’s any tricks to ensure they stay out? I would definitely be concerned.
Randeez 2012 Budget Yukon Denali Build (stick on hood scoops galore)
- Thread starter randeez
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
OP
OP
randeez
Full Access Member
One head down after about three tries lol
Been a while
Forgot the 4 stugs that go in the bottom of the head, realized after starting to put washers on, 2nd time forgot to arplube threads after putting nuts on
Been a while
Forgot the 4 stugs that go in the bottom of the head, realized after starting to put washers on, 2nd time forgot to arplube threads after putting nuts on
OP
OP
randeez
Full Access Member
Forgot you’re under a time crunch.
OP
OP
randeez
Full Access Member
hasnt rained in like 6 months....weekend my heads arrive is fookin pouring
other head is on, the nuts that go on thru the valley/lifter pockets are prob going to give me nightmares. theres no way to put them on by hand. best way i came up with is to put them on the end of a small magnet and try and get it to start threading. but you only have like 30* window to work with. i would get one or two pretty easy. then it would take like an hour to get another, couple more easy ones then another pita one.
finally got them, put valvetrain on one side started raining
other head is on, the nuts that go on thru the valley/lifter pockets are prob going to give me nightmares. theres no way to put them on by hand. best way i came up with is to put them on the end of a small magnet and try and get it to start threading. but you only have like 30* window to work with. i would get one or two pretty easy. then it would take like an hour to get another, couple more easy ones then another pita one.
finally got them, put valvetrain on one side started raining
OP
OP
randeez
Full Access Member
need to order some more stuff...
seems pushrods are too long doing the zero lash and seeing how many turns it takes to get to 25ft lbs, checked the whole side i did get on and they were all nearly 1-3/4 turns (sposed to be 1/2 to at max 1 turn i think). but i should be able to continue with out them so no big deal, just pull the valve covers and throw them in when they get here
going to go ahead and grab new fuel regulator i'll need for larger pump eventually and couple fittings to plumb it all in. that way i can drop the intake manifold back on.
radiator/fan combo i was looking at went on sale, couple bux off but doubt it would drop any more so i grabbed it the other day. going to be asking alot of the little 28" core radiator so hopefully spending the $$ on it will be fine
seems pushrods are too long doing the zero lash and seeing how many turns it takes to get to 25ft lbs, checked the whole side i did get on and they were all nearly 1-3/4 turns (sposed to be 1/2 to at max 1 turn i think). but i should be able to continue with out them so no big deal, just pull the valve covers and throw them in when they get here
going to go ahead and grab new fuel regulator i'll need for larger pump eventually and couple fittings to plumb it all in. that way i can drop the intake manifold back on.
radiator/fan combo i was looking at went on sale, couple bux off but doubt it would drop any more so i grabbed it the other day. going to be asking alot of the little 28" core radiator so hopefully spending the $$ on it will be fine
Bet it was $1400.
OP
OP
randeez
Full Access Member
Bet it was $1400.
No comment
OP
OP
randeez
Full Access Member
It was a little bit cheaper for the record
Back to this point...kind of waiting on pushrods before I close valley so I know they're all in their lifters. Got some other stuff to do so no big deal waiting.
As it turns out these heads are wider that the stock heads on same block by about 1/2" so whatever I did before wouldn't have worked anyway. Added another flex joint, brings the length of them pretty close to equal just for you @iamdub
Back to this point...kind of waiting on pushrods before I close valley so I know they're all in their lifters. Got some other stuff to do so no big deal waiting.
As it turns out these heads are wider that the stock heads on same block by about 1/2" so whatever I did before wouldn't have worked anyway. Added another flex joint, brings the length of them pretty close to equal just for you @iamdub
