What did you do to your NNBS GMT900 Tahoe/Yukon Today?

[Onlyone]

I was taking the drivers seat cover off to steam the foam completely and let it dry but I tore out a couple clips. Usually you can slide them out but since I was leaving the seat in I couldn’t. Oh well. I just ordered a new OEM seat pad. Delivered in 2 days. Installed it today. Huge difference.

 

[992dr]

I was taking the drivers seat cover off to steam the foam completely and let it dry but I tore out a couple clips. Usually you can slide them out but since I was leaving the seat in I couldn’t. Oh well. I just ordered a new OEM seat pad. Delivered in 2 days. Installed it today. Huge difference.View attachment 391883View attachment 391884View attachment 391885View attachment 391886View attachment 391887View attachment 391887

Damn, that looks great.
Can you share where you got your cushions from and did you recover them as well?
Thanks

 

[Onlyone]

Damn, that looks great.
Can you share where you got your cushions from and did you recover them as well?
Thanks

I used my factory cover and bought the OEM pad from Amazon. I pretty much find the OEM part number, google it and then find the cheapest place to get it.

 

[Sam Harris]

Washed my wife's equinox today, first time since possibly October last year. Poor car, was so dirty, the suds were dripping off grey. After it was clean, it made the tahoe look pretty bad so I washed it as well...first time since...mid November or so. All the shop grunge is off it now and its very shiny.

Pics, or INH..

 

[StrkAliteN]

Nice little auto trim removal set onsale Amazon

Hope this helps someone

save a few bucks

obvious struggles to load pics ! hahahaha

 

[Doubeleive]

Nice little auto trim removal set onsale Amazon

Hope this helps someone

save a few bucks

obvious struggles to load pics ! hahahaha


View attachment 391914View attachment 391914View attachment 391914

have you used it? some plastic trim tools are not worth the plastic used to make them

 

[StrkAliteN]

have you used it? some plastic trim tools are not worth the plastic used to make them

No I have not ( just ordered a moment ago )

I need to remove my interior front door panels to trouble shoot stereo speakers

The ratings looked good on Amazon reviews

 

[992dr]

I used my factory cover and bought the OEM pad from Amazon. I pretty much find the OEM part number, google it and then find the cheapest place to get it.

Gotcha
Been doing the same for years.
Thanks again

 

[Doubeleive]

No I have not ( just ordered a moment ago )

I need to remove my interior front door panels to trouble shoot stereo speakers

The ratings looked good on Amazon reviews

harbor freight sells some, they are ok mine have taken some abuse broke some tips/ends in the process, others I have bought are garbage mostly because of being too "soft" and having no pry strength.

 

[89Suburban]

Gents I am having an issue with TPMS relearn after swapping my rear tires from side to side when doing the rear brakes this weekend.

Parking brake set, key on but not running. I can enter the relearn in the DIC menu and activate it. Horn beeps twice and the left front lights up.

I hit the l/f with the trigger tool and it beeps and the r/f lights up.

I go to that r/f wheel and hit the trigger and it beeps TWICE, then the l/f light comes back on??

So I go back to the l/f and hit the trigger and there is no response.

If I skip back to the r/r and hit the trigger the horn beeps once, no lights at all.

l/r wheel no response.

Go back to the menu it's stays stuck in relearn mode. If I key off and back on to force it out it now reads NO sensors reading AT ALL. And the damned TPMS dash light is lit.

I tried this several times to same result.

Should I do a battery disconnect reset to the vehicle? That's all I can think of trying next.