Recent content by Dantheman1540
-
2004 6.0 NV4500 Tahoe
Tahoe made it to work and back so I’m calling the ECT issue mended. I think my next thing to do on it is fix the exhaust. The QTP cutout quit working so I need to diagnose that (prob another burnt up motor from holding the switch to long). If it’s bad I’ll probably just redo the whole damn thing...- Dantheman1540
- Post #4,877
- Forum: Under Construction
-
2004 6.0 NV4500 Tahoe
Those Deaver 64” springs in the rear do the lords work well! The hydro bumps were working well along side them as well. The front is no slouch either, but the front has a lot more down travel than up and doesn’t look as obvious in pics. Iirc I measured 14”front and 17” rear. But I think the rear...- Dantheman1540
- Post #4,876
- Forum: Under Construction
-
2004 6.0 NV4500 Tahoe
Pretty sure I fixed it, the pintail had been sliced previously and it looked like the splice had failed. All fixed and survived a run to the only store in town, the one and only MOPHOin Dollar General. Where I picked up some washing chemicals and gave this sloot a scrubbing. Also gave my...- Dantheman1540
- Post #4,874
- Forum: Under Construction
-
2004 6.0 NV4500 Tahoe
Well my wiring replacement didn’t fix my issue. Tahoe almost left me stranded after it stalled and wouldn’t start twice on my ride home. I think I found a splice in the ECT sensor harness wiring that could be bad. I ended up wiggling it after it wouldn’t start and it made it home after that. So...- Dantheman1540
- Post #4,873
- Forum: Under Construction
-
2004 6.0 NV4500 Tahoe
I’d prefer you come trim around my piece :p- Dantheman1540
- Post #4,871
- Forum: Under Construction
-
2004 6.0 NV4500 Tahoe
Actually spent 30mins looking for this trim piece. I almost thought I threw it out on accident. Eventually I found it under the back seat of the Tahoe luckily not crushed.- Dantheman1540
- Post #4,869
- Forum: Under Construction
-
2004 6.0 NV4500 Tahoe
Shifter dohicky removed, now I gotta remember where I stashed the manual trim piece.- Dantheman1540
- Post #4,868
- Forum: Under Construction
-
2004 6.0 NV4500 Tahoe
Feels good to be working on this again and fine tuning some stuff that had really really really aggravated me for a long time lol.- Dantheman1540
- Post #4,867
- Forum: Under Construction
-
2004 6.0 NV4500 Tahoe
Ok it’s not bad at all, once the column trim is removed it’s just two T25s and 4 connectors which are easy to get to. The lower T25 is kinda a pain in the butt, your probably supposed to remove the steering wheel, but that’s a lot of work and I made it work with a T25bit in a 1/4” wrench. Taping...- Dantheman1540
- Post #4,865
- Forum: Under Construction
-
2004 6.0 NV4500 Tahoe
When your snipped, raw dog is life.- Dantheman1540
- Post #4,864
- Forum: Under Construction
-
2004 6.0 NV4500 Tahoe
I think I’ll attempt it in the morning, I’ll pull the one out of my RCSB- Dantheman1540
- Post #4,862
- Forum: Under Construction
-
Free to me 1996 GMC
Went down and cleaned my shop up a bit before work and drove the dirt road way in the gmc. I’ve got close to 30miles on it so far with no issues, I think that warrants getting a spare set of keys made. Anyway decided I’d see how bad this 4l80 first gear is and it impressed me! 1st gear and...- Dantheman1540
- Post #46
- Forum: General Discussion
-
Free to me 1996 GMC
I was actually looking for what plate I should get not the verbiage because the trucks kinda too stock imo for a custom name plate. But I might do like save the cougars or something plate. There’s so many options in fl it crazy.- Dantheman1540
- Post #45
- Forum: General Discussion
-
Free to me 1996 GMC
I must let you know, the PO of this truck showed me some play bois on like my 12th B day when he took me shooting, with no hearing protection. Anyway he would approve of these ideas- Dantheman1540
- Post #43
- Forum: General Discussion
-
Free to me 1996 GMC
How about LORGEKAK, BIGWANG, or COKBBIG?- Dantheman1540
- Post #42
- Forum: General Discussion
