Does any use a Fumoto oil pan drain valve?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Stbentoak

Full Access Member
Joined
Jul 20, 2020
Posts
1,666
Reaction score
1,902
It would add a little extra work but again, IMO, if I had that on my oil pan, I would want a small shield there to protect it. Could even have the drain hose already attached and rolled up and tied down to shield and just open the valve and point the hose. I am old. I like things simple. Unscrew a drain plug and retighten it.
What’s simpler than not getting any tools, flipping a lever and draining it with a tube directly into your waste oil container? DEF containers are perfect.
I put a gallon baggie on my filter wrench and as soon as it comes loose, baggie catches all the oil and straight to the trash.
Most time I can do whole process without even 1 drop on the floor…
 

OR VietVet

Multnomah Falls
Supporting Member
Military
Joined
Oct 8, 2014
Posts
20,761
Reaction score
36,737
Location
Willamette Valley
That's a good idea. Are they easy to spray off?
Very easy to spray off and clean. They have a diamond plate design on one side and that allows for good grip. I also roll my floor jack on to them and yesterday I jacked up a transfer case on a Jeep to allow for transmission pan clearance removal and it did not hurt the mat at all. They are tough but soft to lay on. I have had oil, transmission fluid, fuel and diff fluids on them with no problems.
 

BlaineBug

Full Access Member
Joined
Dec 29, 2019
Posts
1,179
Reaction score
668
Location
Clown World
I have concrete driveway and I don't like to lay on it. My girl went to Bi-Mart, here in the PNW, and found these roll up 3/8" thick rubber mats, almost like a yoga mat. I have used them in gravel and dirt and on the concrete. Love 'em. I have 3 of them and stack them sometimes.
Who needs a catch pan when you have the gravel driveway to act as an eternal catch pan? Just returning that black gold right back into the earth where it came from - a real ashes to ashes evolutionary tale!
 

OR VietVet

Multnomah Falls
Supporting Member
Military
Joined
Oct 8, 2014
Posts
20,761
Reaction score
36,737
Location
Willamette Valley
Big fan of Fumoto Valves. Never been easier and cleaner draining oil. I had to replace the little plastic lock on one because it broke when I removed once but it wasn't costly and easy to get. What can be easier than flipping a little lever?
Could that plastic lock have caused a leak?
 

YukonRog

Full Access Member
Joined
Jun 25, 2020
Posts
597
Reaction score
760
Location
Auburn, CA
Could that plastic lock have caused a leak?
No it's just a secondary almost redundant "safety". Since the lever is spring loaded and catches in a groove, it takes a good amount of pressure to push it out so it can be rotated into the open position. The little plastic lock just makes it impossible to push the lever out to rotate it.
 

Rocket Man

Mark
Supporting Member
Joined
Dec 25, 2014
Posts
26,004
Reaction score
50,862
Location
Oregon
I use the Femco which utilizes a drain hose that pushes in a plunger when it’s time to drain the oil. Even if you remove the dust cap, oil can’t flow until you screw the drain hose on which is safer imo. Also, the hose extends downward to direct the oil into the drain pan/ bucket. I went with the 90* elbow hose since the LS drain plugs are on the back of the pan instead of the bottom.
 

YukonRog

Full Access Member
Joined
Jun 25, 2020
Posts
597
Reaction score
760
Location
Auburn, CA
I use the Femco which utilizes a drain hose that pushes in a plunger when it’s time to drain the oil. Even if you remove the dust cap, oil can’t flow until you screw the drain hose on which is safer imo. Also, the hose extends downward to direct the oil into the drain pan/ bucket. I went with the 90* elbow hose since the LS drain plugs are on the back of the pan instead of the bottom.
That's an interesting design. I can see it in some applications. On others, no. I like the Fumoto for it's ability to immediately stop the flow with a flick of the lever. On my truck for example, I use one gallon jugs. I'd be leary of twisting the hose/connector to stop it quickly.
 

Forum statistics

Threads
132,366
Posts
1,866,803
Members
96,989
Latest member
Mreedini
Top