Search results

  1. David Paul

    Rear control arm question....

    As requested......Same Kit as OHSIXX. Belltech 2/3 Free travel mod, DJM endlinks, panhard bar. Also did the bigger brakes from NNBS series, electric fan with OEM harness, vet trans servo, Airaid intake. The wheels are new to me 20". Need a tune, on the BB waiting list for NJ
  2. David Paul

    Rear control arm question....

    Thank you both for the replies. I'm on 20's so I should be good to go.......you've put my mind at ease. I should be done tomorrow..
  3. David Paul

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Agreed,who knew about scrubbing bubbles but it really works well. Follow up with a good leather conditioner. Will look like new.
  4. David Paul

    Rear control arm question....

    I'm finishing up the installation of a Bellrech 2/3 kit for my 04 Tahoe. What if anything should I do with/to the rear control arms? I see Belltech has a relocation bracket. I also see a full adjustable kit for the upper and lower arms. I have tha panhard bar and understand the need for it along...
  5. David Paul

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    I'm betting 2/3. I recognize the box contents. I'm finishing up the same kit myself. Front almost done.
  6. David Paul

    Black Bear Performance Tune Somerset, NJ 1-3 May, 2016

    Done.....
  7. David Paul

    Black Bear Performance Tune Somerset, NJ 1-3 May, 2016

    Figures......waited too long. Any chance for a waiting list in case of cancelation?
  8. David Paul

    Spring Orientation?

    Thanks for the quick reply Nathan, I'm going with it
  9. David Paul

    Spring Orientation?

    So I'm in the process of installing new Balltech lowering springs on my 2004 Tahoe. I've looked and have seen conflicting information. Which way are the springs installed? Tight (closer together) coils to the top or bottom? I'm thinking tighter coil to the bottom so the print "Baelltech" is...
  10. David Paul

    Easy 4-Hi mod - Simple All High Chip 03-06 model years

    2007 Tahoe fuse box is different then the "classic" 07 1500 series.
  11. David Paul

    Steering wheel lock

    My 04 Tahoe does not which surprised me. I'm guessing yours does not either. Good question though.
  12. David Paul

    Difference between 2003 and 2006 Yukon?

    Agree on the hydro boost. I was looking into the upgrade mod, not really looking forward to it. Opened the hood to check on something else and damn, what did I notice, my 04 had the hydro boost. Checked that off the to do list.
  13. David Paul

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Did the "free travel" mod in preparation for my 2/3 Belltech lowering kit......did the front hubs yesterday to take care of front end noise. Needed new rotors because of the bad bearing, so I ordered the parts for the brake upgrade from a 2008 Tahoe. Since the truck is out of service for a week...
  14. David Paul

    NBS OEM Factory Floor Mats-Gray FS

    Yea I agree with you guys but while I'd like these, I need front wheel hubs (240) for parts and knock sensor/intake gasket to cure mil.......so funds are a little tite right now...
  15. David Paul

    Seat Heater auto on?

    Good morning Clayton, I only did the drivers side as 90% of the time it's just me getting in it when cold. If you wanted to do both I would use 2 relays or a dpst relay to keep the two circuits isolated. I would not assume the wire color code would be the same on the passenger side. It might be...
  16. David Paul

    NBS OEM Factory Floor Mats-Gray FS

    Would you consider $40 ?
  17. David Paul

    Seat Heater auto on?

    Terminal 85 was attached to the negative momentary trigger from my Viper remote. Terminal 86 to constant 12+ Terminal 30 to the brown wire from the door seat heater switch Terminal 87 to the blue wire. Hope this helps.
  18. David Paul

    Rear Dif

    This, I just did mine last week. Be careful not to over fill it. The correct level is about a 1/4 inch below the fill hole.
  19. David Paul

    Seat Heater auto on?

    Ok, now that winter is over, I have this figured out. I set up one of the aux functions on the remote to control a relay. The aux output momentarily powers the relay. The relay then acts as a momentary spst switch. At the seat heat switch on the drivers door, there are 12 wires coming out. The...
  20. David Paul

    Left turn noise

    Lol......yea, I've done that too.... Great minds think alike
  21. David Paul

    Left turn noise

    Travis, Check the ABS & Traction control activates for no reason thread in the General Discusion section. I believe that is my issue. Hope this helps. Since I have 150,000 miles on mine, I'm going to replace both front hubs to see if that fixes the issue. If not, at least I won't have to worry...
  22. David Paul

    Left turn noise

    When I turn left, it sounds as if the abs is kicking in. It happens mostly when the truck is cold and only on the first couple of left turns. Sound coming from left front. Power is decreased, but no abs active light comes on.if I lift off the gas, noise stops and everything seems fine until the...
  23. David Paul

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Gear oil change in the front differential and transfer case. Trans servo mod completed and Airaid cai installed. Another good day in the garage. Very happy with the intake and servo mod. Noticible improvements but not harsh shifting nor too loud at WOT.
  24. David Paul

    Center console led light mod

    David, Please stop. I never would have thought of any of these but now I MUST do them all....... Great ideas.....
  25. David Paul

    Installing Brake Controller

    Get a vehicle specific harness for the model brake controller you have and your 01 Yukon. About $20. Plug one end in as Mr 960 said, the other end to the brake controller. Plug and play, done deal. 40 mins tops including mounting the controller.

Forum statistics

Threads
132,332
Posts
1,866,201
Members
96,957
Latest member
beka1283

Latest posts

Top