Search results

  1. Mickey_7106

    What did you do to your NNBS GMT900 Tahoe/Yukon Today?

    What's weird is that the crimped end was super easy to pull out of the plug once it ripped off the wire
  2. Mickey_7106

    What did you do to your NNBS GMT900 Tahoe/Yukon Today?

    How can I prevent these wires from sticking to the plug? 5 out of the 8 ended up breaking. This set has been on since 2019 roughly about 60k miles
  3. Mickey_7106

    What did you do to your NNBS GMT900 Tahoe/Yukon Today?

    Broke these plastic pieces that hold the map sensor. Can that round piece that holds the sensor be replaced?
  4. Mickey_7106

    What did you do to your NNBS GMT900 Tahoe/Yukon Today?

    Anyone know if the wire that clips to the side of the backrest can be replaced? Mine is broken on one side
  5. Mickey_7106

    Maintenance items for the win and the joys of rust free work!

    Glad I stumbled into this thread as I also have a "choppy" idle at stop lights. I thought maybe an engine mount was bad (replaced driver side only 2 years ago) My truck has about 154k miles, so it due for some maintenance. For the O2 sensors, which brand did you go with? I see quite a few...
  6. Mickey_7106

    What did you do to your NNBS GMT900 Tahoe/Yukon Today?

    Changed the oil yesterday. Ordered some more KnN filters thinking i was out. Anyone else noticed the change in design? The new filter is a bit shorter and it has more holes near the gasket. New and old filter were bought on amazon
  7. Mickey_7106

    180K miles - do O2 sensors?

    Are bosch good sensors? I only see gm downstream sensors for my 09 5.3 on rockauto
  8. Mickey_7106

    180K miles - do O2 sensors?

    I googled it. Thought there was only 1 after the third cat
  9. Mickey_7106

    180K miles - do O2 sensors?

    These trucks have 4 sensors? Thought only 3 because of y pipe
  10. Mickey_7106

    Rennen Forged M-6 Monolicht 24" x 10" Wheels - Opportunity for Brand New Custom Finish

    I hate being broke . Wheels look nice. Glws
  11. Mickey_7106

    Service stabilitrak, traction control warning :(

    Same thing happened again this week. Theres also a code for the driver heater open or shorted. After doing some search the same code can cause the tcm to trip out? Anyways look what i found. Hope this resolves these trans issues. The wires are melted under the seat
  12. Mickey_7106

    What did you do to your NNBS GMT900 Tahoe/Yukon Today?

    Newb question. Is the PCM located next to the second battery tray towards the front of the vehicle? Trying to track down codes P0700, U0073, U0100
  13. Mickey_7106

    What did you do to your NNBS GMT900 Tahoe/Yukon Today?

    What part numer are these? Sfks website is crap. Assuming they're 4wd right?
  14. Mickey_7106

    How to Test Wires So I can cut dead wires?

    Here's what i do to isolate unnecessary wires Cut a small length of proper size heat shrink and have go past the wire just enough to pinch and create a seal
  15. Mickey_7106

    How to Test Wires So I can cut dead wires?

    Assuming that you don't need any of those wires for anything else, i would disconnect the battery and cut back all of it and shrink wrap the ends individually, so that they don't accidentally make contact with metal or other bare wires. Removing the knee covers of the dash may offer more room...
  16. Mickey_7106

    How to Test Wires So I can cut dead wires?

    are you deleting an aftermarket sound system?
  17. Mickey_7106

    What did you do to your NNBS GMT900 Tahoe/Yukon Today?

    Also, years ago I remember someone doing a write up for modifying the stock airbox and inner fender to allow more air to flow through? Does that sound familiar?
  18. Mickey_7106

    What did you do to your NNBS GMT900 Tahoe/Yukon Today?

    Good morning, does anyone know if there are replacement grommets for the under side of the stock air filter box?
  19. Mickey_7106

    P2138 Throttle / Pedal Position

    I replaced the pedal and the problem went away. I can't find the video on yt, but there was one that shows you how to probe the harness and check for voltage for each sensor. Most videos just show how to replace it.
  20. Mickey_7106

    P2138 Throttle / Pedal Position

    P2138 Throttle / Pedal position sensor / switch "D" / E Voltage Correlation Hello All, Saturday night, i got this code merging on the freeway trying to go WOT. Half way through WOT the truck fell on its face and a bunch of service this and that messages appeared and it went into reduce power...
  21. Mickey_7106

    Tech2 and SPS2 programing

    How so?
  22. Mickey_7106

    Tech2 and SPS2 programing

    It was on a windows 10. Gave up on it and returned it
  23. Mickey_7106

    VCX Nano and tech2win

    Chinacardiags is better written but has the same missing or broken links for download.
  24. Mickey_7106

    VCX Nano and tech2win

    Thanks, I'll try them. Vxdiag.com is confusing.
  25. Mickey_7106

    VCX Nano and tech2win

    Hi everyone, I'm having a difficult time setting up the nano to work with tech2win. After several attempts of installing software im stuck with the tech2win app not recognizing the nano. When i plug the nano via usb , vx manager and Gm vci recognize it as plugged in. Gm mdi and tech2win wont. I...

Forum statistics

Threads
132,714
Posts
1,873,072
Members
97,537
Latest member
CHENTE

Latest posts

Top