Blazed's 2011 Tahoe Build

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Status
Not open for further replies.
OP
OP
Blazed

Blazed

Accepting Donations
Joined
Dec 20, 2010
Posts
4,243
Reaction score
10
I think he's just tripping about tony flaming him up he'll be back he loves me and you too much to leave.
 

07Burb

GM fan for life
Staff member
Administrator
Supporting Member
Joined
Jan 3, 2011
Posts
50,348
Reaction score
17,132
I think he's just tripping about tony flaming him up he'll be back he loves me and you too much to leave.

Flaming him after some srt8 fanboy statements :lol:
 
OP
OP
Blazed

Blazed

Accepting Donations
Joined
Dec 20, 2010
Posts
4,243
Reaction score
10
He was dumb to start that argument honestly.

---------- Post added at 02:15 PM ---------- Previous post was at 02:10 PM ----------

At the dealer now.
Only 4x4 I could find was z71 and those have different springs I think so that's still not a good comparison but compared to all the 2wd normal Tahoe it was 1 inch higher all around.
Based off a 2wd normal Tahoe I'm getting 2 1/4 drop in the rear and 2 inches in the front.

---------- Post added at 03:27 PM ---------- Previous post was at 02:15 PM ----------

Guys when I get back in town I am taking the rear hardware kit off of my truck. I will be putting the belltech extenders back on and calling it a day. I am only down two 1/4 inches in the rear and I most definitely do not need that POS hardware kit on there making noise and making my trailing arms hang low and look cheap. Ill never put anything from DJM on any car I own ever in the future. I will be keeping the shorter endlinks and swaybar relocation because I cannot easily go back to the stock location.
I would really advise everyone to stay away from the rear hardware kit if you arent going down like 5 inches. It is a pain in the ass and now thats its fallen apart once Im scared it will happen again.

---------- Post added at 03:30 PM ---------- Previous post was at 03:27 PM ----------

**** it I'm doing it now I dont want this shit on my car anymore.
 

Modded

That Guy
Joined
May 3, 2009
Posts
6,942
Reaction score
108
I think he's just tripping about tony flaming him up he'll be back he loves me and you too much to leave.

I just read a bit of that exchange. I would have hopped in just to chop Tony up if it was not his thread.
He has no right to say shit to anyone on here as much as he lies........:gr_grin:
If he was local and attended car meets, I would ride up to one of them and pull his card in front of everyone.

---------- Post added at 01:33 PM ---------- Previous post was at 01:30 PM ----------

He was dumb to start that argument honestly.

---------- Post added at 02:15 PM ---------- Previous post was at 02:10 PM ----------

At the dealer now.
Only 4x4 I could find was z71 and those have different springs I think so that's still not a good comparison but compared to all the 2wd normal Tahoe it was 1 inch higher all around.
Based off a 2wd normal Tahoe I'm getting 2 1/4 drop in the rear and 2 inches in the front.

---------- Post added at 03:27 PM ---------- Previous post was at 02:15 PM ----------

Guys when I get back in town I am taking the rear hardware kit off of my truck. I will be putting the belltech extenders back on and calling it a day. I am only down two 1/4 inches in the rear and I most definitely do not need that POS hardware kit on there making noise and making my trailing arms hang low and look cheap. Ill never put anything from DJM on any car I own ever in the future. I will be keeping the shorter endlinks and swaybar relocation because I cannot easily go back to the stock location.
I would really advise everyone to stay away from the rear hardware kit if you arent going down like 5 inches. It is a pain in the ass and now thats its fallen apart once Im scared it will happen again.

---------- Post added at 03:30 PM ---------- Previous post was at 03:27 PM ----------

**** it I'm doing it now I dont want this shit on my car anymore.
DJM shit is just at the bottom of all drop parts. Overpriced rubbish with no quality control. Funny because Tony pushes that rear hardware kit as much as he possibly can. Next time around I am using McG parts for all my drop needs, and then using Belltech rear coils. No DJM shit for me.
 

MACHO

Full Access Member
Joined
Aug 10, 2012
Posts
1,540
Reaction score
5
Location
Seattle, WA
Status
Not open for further replies.

Forum statistics

Threads
132,367
Posts
1,866,823
Members
96,992
Latest member
a-reem

Latest posts

Top