Cruise Control, Intermittent...

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Wolfbraid

Full Access Member
Joined
Aug 30, 2018
Posts
283
Reaction score
271
Location
Winston Salem, NC
So back from another road trip, this issue has happened before but I don't use cruise that often so I forget about it.

Anyway so from time to time the Cruise will not engage, light on steering wheel lights up, but when you
press "SET" or resume the cruise indicator in the dash cluster doesn't come on and cruise doesn't hold.

a few miles later(or whenever) if you try it, it works... seemingly no particular reason why.

I have no lights on dash(other than tire pressure)
No codes in ecu that I'm aware of(I'll pull codes see if there are any ones in history, on Tuesday)

Otherwise good trip averaged 18.1 on the way up, and dropped to 17.1 on the way back.
 

LanceD

Full Access Member
Joined
Jan 16, 2018
Posts
338
Reaction score
323
Location
Abq
Mine did this to me today also. Curious.
 

BourbonNcigars

Full Access Member
Joined
Dec 1, 2018
Posts
865
Reaction score
1,840
Replace the brake switch under the dash. 25981009 or D1539J

GM OE or ACDelco Professional only.
Yep. Mine is on its way out. One trick that works for me is to turn the cruise on, tap the brake pedal very lightly, then hit set. Works 99% of the time for me if I do that. I use cruise every single day.
 

Hi-psi

Full Access Member
Joined
Mar 10, 2018
Posts
305
Reaction score
455
Location
Atlanta, GA
As others said, brake pedal switch. I replaced my failed one less than a year ago with a generic brand one from NAPA. Didn't last a year. A few weeks ago replaced it with an OEM one. Hopefully it lasts a little longer. Luckily, it's only about a $10 part.
 
OP
OP
Wolfbraid

Wolfbraid

Full Access Member
Joined
Aug 30, 2018
Posts
283
Reaction score
271
Location
Winston Salem, NC
Funny the switch is mentioned, I was guessing it might have been that, a few months ago when I pulled codes, there was a brake switch soft code(wasn't setting off a CEL) Yay! Thanks.
 

Reggie Holland

TYF Newbie
Joined
Apr 22, 2019
Posts
3
Reaction score
0
Having the same issue, but have to pull over kill the engine, open the door to turn off the accy timer and crank back up. Then it will usually work. When it doesn't work, it is from crank up. Have replaced the brake switch with Delco part. Symptoms did not change with brake switch change. The radio also does weird stuff at times with the steering wheel controls. Vol up or down will cause another function to work as well as memory advance or retard. After a while, everything works as it should. Also the controls on the front of the radio always work correctly. I was wondering if it could be the BCM on my 2007 Yukon XL causing these issues.
 

swathdiver

Full Access Member
Joined
May 18, 2017
Posts
19,758
Reaction score
26,643
Location
Treasure Coast, Florida
Having the same issue, but have to pull over kill the engine, open the door to turn off the accy timer and crank back up. Then it will usually work. When it doesn't work, it is from crank up. Have replaced the brake switch with Delco part. Symptoms did not change with brake switch change. The radio also does weird stuff at times with the steering wheel controls. Vol up or down will cause another function to work as well as memory advance or retard. After a while, everything works as it should. Also the controls on the front of the radio always work correctly. I was wondering if it could be the BCM on my 2007 Yukon XL causing these issues.

Could be Reggie. My 2006 Pontiac Montana with this same CanBus architecture did that with the radio controls on the steering wheel. It required a re-flash of the BCM or maybe a new one, don't remember, it was under warranty.

Check your grounds and battery cables and the age and health of the battery. A bad cell or loose/dirty ground can cause all kinds of gremlins. Best way to get at this problem is with bi-directional scan tool though like the Tech-2 along with the shop manual.
 

Reggie Holland

TYF Newbie
Joined
Apr 22, 2019
Posts
3
Reaction score
0
Thanks for the response, James. Battery is new and the problem existed with the previous battery. I have checked for difference in potential with the engine running with a DVM between the negative post of the battery and chassis and there is none.
 

Randy Whistler

Living the dream! I'm just not sure who's dream
Joined
Dec 12, 2017
Posts
139
Reaction score
65
Location
In Hell, but I've got a Tahoe!
OK, this may be a stupid thought, but does the cruise interact with the ABS or airbag system? In my 'hoe, the relays for both ABS & airbags have been pulled, and the cruise control doesn't work - does the same thing as described here. May be off base but might be related somehow Worst case, can eliminate something. . . ;)
 

Forum statistics

Threads
132,730
Posts
1,873,298
Members
97,559
Latest member
blanchard7684

Latest posts

Top