97YukonNZ
Full Access Member
- Joined
- Feb 12, 2021
- Posts
- 1,381
- Reaction score
- 3,767
Could be how you've wired it. Might just be lights showing n that's all?
Thought about wiring to cig lighter power? Guess then it would be on all the time then tho
Tonyrodz's Tahoe Build Thread
- Thread starter Tonyrodz
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
Thought about wiring to cig lighter power? Guess then it would be on all the time then tho
Snowbound
Jim
Should only be 2 wires to connect it. I would think if it’s lit up it should be working. Maybe a bad charging cable?
OP
OP
Tonyrodz
Resident Resident
Yup, only per and ground. Both hooked up. I've used different cables to rule that out. Cables are good.
That's why I wired it to keyed pwr. I didn't want it lit at night while it's parked. Sometimes it sits over a week without starting it. I know LEDs don't draw alot of pwr, but I still don't want it constantly on.Could be how you've wired it. Might just be lights showing n that's all?
Thought about wiring to cig lighter power? Guess then it would be on all the time then tho
Back to basics, and end the soap opera. Verify the input voltage and if that's good, substitute your old socket and a phone charger. Maybe your new adapter is defective.
Verify the input voltage and if that's good, substitute your old socket and a phone charger. Maybe your new adapter is defective.
OP
OP
Tonyrodz
Resident Resident
Just documenting my steering shaft replacements.
Did upper and lower shafts. Pain in the balls like everything else on this Hoe! Done--but to 90% correctness. Call it good for government work!
Pics to satisfy all you voyeurs!
Upper shaft. It's best to remove the gas pedal to get to the bolt.
Check out the differences between the old oem design compared to the new design. OEM is on top. I separated the upper shaft into 2 pieces. SPLINES!!
Did upper and lower shafts. Pain in the balls like everything else on this Hoe! Done--but to 90% correctness. Call it good for government work!
Pics to satisfy all you voyeurs!
Upper shaft. It's best to remove the gas pedal to get to the bolt.
Check out the differences between the old oem design compared to the new design. OEM is on top. I separated the upper shaft into 2 pieces. SPLINES!!
OP
OP
Tonyrodz
Resident Resident
New shafts together.
youtube.com
New lower shaft play from banging it--
youtube.com
Compared to the old shaft play--I didn't bang this one in place--
youtube.com
New Upper And Lower Shaft Wobble
youtube.com
New Lower Shaft Inlet Stretched
youtube.com
Old Lower Shaft Play
youtube.com
Last edited:
97YukonNZ
Full Access Member
- Joined
- Feb 12, 2021
- Posts
- 1,381
- Reaction score
- 3,767
Nice work!
Looks pretty involved. Did you find any steering sensors on your journey?
97YukonNZ
Full Access Member
- Joined
- Feb 12, 2021
- Posts
- 1,381
- Reaction score
- 3,767
Hey looking at the 1st clip,is that shaft supposed to roll over straight or is it okay to have a slight bend in it. Can you see that from the cab while turning the wheel?New shafts together.
New lower shaft play from banging it--New Upper And Lower Shaft Wobble
Compared to the old shaft play--I didn't bang this one in place--New Upper And Lower Shaft Wobble
New Lower Shaft Inlet Stretched
OP
OP
Tonyrodz
Resident Resident
I think there was a steering sensor above the shaft where it's bolted to the column--
It's the round white disc in the upper left of the pic.
97YukonNZ
Full Access Member
- Joined
- Feb 12, 2021
- Posts
- 1,381
- Reaction score
- 3,767
Yes I was looking at that. I have a surge in the p.s sometimes turning right. I have been told that sensor is the reason why.
