What did you do to your OBS GMT400 Tahoe/Yukon Today?

[blue99tahoe24]

Thanks guys, and its original paint. She will be 13 yrs old in Jan. Wheels been on for 7 yrs straight.


Sent from E.T's Phone using Tapatalk.

Same here O.G paint ppl think i had it painted tho 7yrs on the wheels damn

foot to the floor

 

[Tricky]

tho 7yrs on the wheels damn

foot to the floor

Yes 7, that I was I done with the chrome wheels because I got tired of swapping out in the winter and back on in spring and they still peeled up. But was walking into a wheel shop and was going to get some Choppers and the UPS guy was right behind me with that fresh set non on the street then and told me I can get those in 22 with Nitto's for $1800 out the door locks, lugs, and mounted and havent been off yet except for warranty work and on 3rd set of tires.




Sent from E.T's Phone using Tapatalk.

 

[Tricky]

foot to the floor

I wired my taillight circuit board to make both both bulbs to light up when brakes are applied. Did that until I can get the LED taillights here I want.
http://www.amazon.com/gp/aw/d/B0015PPWD4/ref=mp_s_a_1?qid=1350826332&sr=1-4&pi=SL75

Here are pic's of what I did to factory tails.




Sent from E.T's Phone using Tapatalk.

 

[blue99tahoe24]

I wired my taillight circuit board to make both both bulbs to light up when brakes are applied. Did that until I can get the LED taillights here I want.
http://www.amazon.com/gp/aw/d/B0015PPWD4/ref=mp_s_a_1?qid=1350826332&sr=1-4&pi=SL75

Here are pic's of what I did to factory tails.
View attachment 18637
View attachment 18638


Sent from E.T's Phone using Tapatalk.

That looks pretty sick how did u do it

foot to the floor

 

[Tricky]

Here is the thread. This is not my write up, got from another forum site.









Ok I just did this mod and snapped a few pics along the way :eyecrzy:



Went from this:



To this:



1st step get the lights out of the truck :smokin:





2nd I located a place where i could solder in to the curcuit board. I took a knife to open up the spots a little bigger:





Then I soldered 2 wires to the curcuit board (sorry the pics a a bit blurry):







Then I routed the wires up the curcuit board and soldered them to the "bright" side of the upper bulb (should be the outer contacts on the bulb):











Make sure when you route the wires that they aren't under the seal (to pervent leaks) or against the bulbs cause they do get hot!








Sent from E.T's Phone using Tapatalk.

 

[kaoticlife]

I'm gonna try this!

sent from tapatalk2 using rabbit ears and aluminum foil.

 

[Gzes]

Nice i gotta try it because my tuner lookin tails suck with light output and i need something until i get my leds

 

[Tricky]

I'm gonna try this!

sent from tapatalk2 using rabbit ears and aluminum foil.

I see how you did the sockets for the 194 bulbs on tali lights I may try that one also.


Sent from E.T's Phone using Tapatalk.

 

[kaoticlife]

They fit in real tight which is a good thing!

sent from tapatalk2 using rabbit ears and aluminum foil.

 

[Gzes]

Shined my tires. It looks perdy now with shiny tires n hummer rims still gotta sand down the ass marks on the roof but dont have the time to just get at it all day then prime...