Window trim

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Doubeleive

Wes
Supporting Member
Joined
Nov 7, 2017
Posts
26,464
Reaction score
39,824
Location
Stockton, Ca.
gm probably got tired of having to glue or tape new pieces on when they fell off it was a big complaint on some of the k2's
 

KMeloney

Full Access Member
Joined
May 2, 2009
Posts
2,901
Reaction score
327
OP
OP
blkonblk

blkonblk

Supporting Member
Joined
Dec 22, 2011
Posts
993
Reaction score
90
Location
NYC
Looks great, BTW.

Did you break [the backing of] the trim when you removed the original pieces, leaving those riveted pieces behind/attached to the truck? And did the new pieces come with a rivet post that went through a hole in the body that needed to be sandwiched from the inside of the truck?
I drilled the rivets out and they come off. I bought a rivet tool on amazon and put new rivets in
 

Doubeleive

Wes
Supporting Member
Joined
Nov 7, 2017
Posts
26,464
Reaction score
39,824
Location
Stockton, Ca.
Looks great, BTW.

Did you break [the backing of] the trim when you removed the original pieces, leaving those riveted pieces behind/attached to the truck? And did the new pieces come with a rivet post that went through a hole in the body that needed to be sandwiched from the inside of the truck?
rivets are easily removed by drilling the center part a little bit and they fall apart and are easily replaced as shown in his photos been this way since forever.
original rivets may be inserted differently, pressed, etc depending on the application
ever hear the term "Rosie the Riveter"
 

KMeloney

Full Access Member
Joined
May 2, 2009
Posts
2,901
Reaction score
327
Last question on this (I think)... Could you have kept the existing riveted plastic mounting piece in place, and mounted the new trim without really using that point to retain the new trim? IOW, are there enough mounting points for the new trim outside of that existing riveted piece that you could have just bypassed the removal of that rivet? Maybe use some double-sided tape there like they've used forever to mount trim?
 
OP
OP
blkonblk

blkonblk

Supporting Member
Joined
Dec 22, 2011
Posts
993
Reaction score
90
Location
NYC
Last question on this (I think)... Could you have kept the existing riveted plastic mounting piece in place, and mounted the new trim without really using that point to retain the new trim? IOW, are there enough mounting points for the new trim outside of that existing riveted piece that you could have just bypassed the removal of that rivet? Maybe use some double-sided tape there like they've used forever to mount trim?
in theory you could but hard to secure it. The chrome part has clips that connects to that molding and without taking out the molding there is no way to bend the clips and secure it. In the below pic I tried to do that. The chrome part bends and goes to waist
IMG_5731.pngIMG_5732.jpeg
 

91RS

Full Access Member
Joined
Nov 15, 2009
Posts
2,594
Reaction score
2,045
Location
GA
There is no advantage to trying to take the pieces apart. They’re not cheap and easy to break. It’s just a couple of rivets.
 
OP
OP
blkonblk

blkonblk

Supporting Member
Joined
Dec 22, 2011
Posts
993
Reaction score
90
Location
NYC
There is no advantage to trying to take the pieces apart. They’re not cheap and easy to break. It’s just a couple of rivets.
this. I didn’t even know what a rivet was until I ran i to this. They come off very easy with a drill, literally 5 seconds of drilling
 

Forum statistics

Threads
132,677
Posts
1,872,435
Members
97,483
Latest member
Bryon Morgan
Top