never researched what ohm's it takes, I am sure it is posted on a thread on here somewhere
any idea's @iamdub ? @swathdiver ? @randeez ?
2017 Yukon Denali Rear Shock Replacement
- Thread starter MobileHomie
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
any idea's @iamdub ? @swathdiver ? @randeez ?
swathdiver
Full Access Member
Joseph Garcia
Supporting Member
- Joined
- Aug 2, 2018
- Posts
- 7,080
- Reaction score
- 9,456
I've seen resistors anywhere from 4 to 20 OHMS, and a size of 10 to 50 watts. As such, I don't believe that the actual resistance is all that critical, as long as it approximates these ranges.
gyukon1978
TYF Newbie
- Joined
- Mar 11, 2024
- Posts
- 8
- Reaction score
- 2
Just replaced both front and rear shocks on my 2017 Yukon Denali with Arnott mr3840 front and Arnott mr3626 rear (magneride z95). Couldn't be happier. Took 6hrs total on my own. Yukon is rock solid back to factory specs (I didn't level and kept the front bias). I also replaced the sway bar links and bushings while i had the truck up on jack stands. Easy, cheap. Used ACDelco links and bushings. Carparts.com for shocks, rockauto for sway bar links and bushings. 2k v 5k+ at dealership.
MobileHomie
Full Access Member
- Joined
- Oct 15, 2021
- Posts
- 123
- Reaction score
- 103
I am bumping this thread because I am not happy with the performance of the Arnott MR 3626 magnaride rear shocks. Still the rear end is still bouncing around. Even did the old put your weight on the rear bumber to bounce it, stopped moving on the third bounce.
When I replaced the fronts with Fox coilovers, I purchased and installed this shock sim.
Vendor told me this would still work with the magnaride rears or work as a sim with passive shocks. Could this thing be causing me trouble, or should I pursue warranty on the shocks?
When I replaced the fronts with Fox coilovers, I purchased and installed this shock sim.
Vendor told me this would still work with the magnaride rears or work as a sim with passive shocks. Could this thing be causing me trouble, or should I pursue warranty on the shocks?
MobileHomie
Full Access Member
- Joined
- Oct 15, 2021
- Posts
- 123
- Reaction score
- 103
Well, I am back to report that the issue was completely mine. The electrical connection on the right rear shock was not seated, the o-ring type seal had escaped the grove and was jammed in the bottom of the socket. Removed the o-ring, lubed with dielectric grease and it went right together, like a hotdog down the hallway, so to speak.
DeDadi
TYF Newbie
- Joined
- Jul 14, 2024
- Posts
- 6
- Reaction score
- 2
Hello I’m pretty confused as to what to do with suspension on my Denali. Did you ever sort your suspension out?
Last edited:
MobileHomie
Full Access Member
- Joined
- Oct 15, 2021
- Posts
- 123
- Reaction score
- 103
No not really. I ditched the Arnott magnaride clones in favor of OE GM and am still not happy with it. I think the issue is different shock rates between the passive Fox coilovers on the front and the OE electronics in the rear. I think I need passive rears with air leveling.
DeDadi
TYF Newbie
- Joined
- Jul 14, 2024
- Posts
- 6
- Reaction score
- 2
Well I bit the bullet and bought the Arnott MR replacements. It feels pretty nice for now but it’s only been a few days. I’m trying to figure out my rear end though.
I did the Maxxtrac rear drop kit last month that comes with the lowering springs and relocating brackets. Unfortunately I think it’s a bit much of a drop in the back and I’m trying to go up an 1”to have a little more shock travel. Not entirely sure how to achieve this.
Similar threads
