I didn't look up the codes. but just as info, if you mean your torque converter is locking and unlocking a lot. I've heard of it being a brake light switch. it you touch the brake it unlocks the converter. so if the switch is intermittent it can cause it to lock and unlock
What did you do to your NNBS GMT900 Tahoe/Yukon Today?
- Thread starter phattyford
- Start date
Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.
I didn't look up the codes. but just as info, if you mean your torque converter is locking and unlocking a lot. I've heard of it being a brake light switch. it you touch the brake it unlocks the converter. so if the switch is intermittent it can cause it to lock and unlock
Mickey_7106
Full Access Member
How can I prevent these wires from sticking to the plug? 5 out of the 8 ended up breaking. This set has been on since 2019 roughly about 60k miles
Mickey_7106
Full Access Member
What's weird is that the crimped end was super easy to pull out of the plug once it ripped off the wire
It's one of the few things I hate on these rigs. I don't know the answer. I tried dielectric grease on the boots, they still rip off. I got special pliers, nothing works. I keep a set of spare wires on hand just because of this. I got a messed up #7 cylinder I got to check the plug on once in a while.
@Trey Hardy
I have not ran any short wires or headers in years but when I did the fix was to use ceramic wires and/or a protective covering, fire resistant cover something like these
they worked quit well. they worked as designed.....
the heat is what causes the problem, that's why the oe wires have a heat shield
8x Spark Plug Wire Boot Heat Shield Protector Insulator Fire Sleeve Protect Boot | eBay
Find many great new & used options and get the best deals for 8x Spark Plug Wire Boot Heat Shield Protector Insulator Fire Sleeve Protect Boot at the best online prices at eBay! Free shipping for many products!
www.ebay.com
dielectric on the boots and keep the metal heat shields on and I've never pulled one out. I do have the special pliers too thou?
just twist them to break the seal and pull while wiggling. haven't broken one on an ls, I don't think ever. pulled some out of the old sbc cheap wires thou.
I run Magnecor on the ls3 car. guys complain about them pulling out, but had them off countless times without issue but that is with heat shield.
just twist them to break the seal and pull while wiggling. haven't broken one on an ls, I don't think ever. pulled some out of the old sbc cheap wires thou.
I run Magnecor on the ls3 car. guys complain about them pulling out, but had them off countless times without issue but that is with heat shield.
Grady_Wilson
Supporting Member
I replaced the 12v power outlet bezels and covers.
One was broken off completely and the other one was just barely hanging on for the last year.
RA had genuine GM pieces for like $3.67 each plus shipping.
I should have ordered some extras but I want to add USB outlets to at least one of the power outlets.
One was broken off completely and the other one was just barely hanging on for the last year.
RA had genuine GM pieces for like $3.67 each plus shipping.
I should have ordered some extras but I want to add USB outlets to at least one of the power outlets.
Attachments
Last edited:
RooTBeeRthe1st
Full Access Member
- Joined
- Jul 11, 2018
- Posts
- 1,085
- Reaction score
- 2,464
Finally washed the outside, interior needs a deep clean.
Coolant is a tad low. Didn't check oil but I'm sure it's below full.
Also dash crack is getting worse... been stable for a few years with 1 small crack between the airbag and defrost vents.
Now it's still that one crack, but the dashboard started to drop down about 3/8" below where it should be.
Probably going to look into pulling the cover out and some plastic weld of something to brace it and flush again...we shall see.
Coolant is a tad low. Didn't check oil but I'm sure it's below full.
Also dash crack is getting worse... been stable for a few years with 1 small crack between the airbag and defrost vents.
Now it's still that one crack, but the dashboard started to drop down about 3/8" below where it should be.
Probably going to look into pulling the cover out and some plastic weld of something to brace it and flush again...we shall see.
I am pleased to report that my driver's side floor pan is now finally bone dry after sealing the shark fin.
I also got a rash of sh*t from co-workers, F & F about the factory rims, so I swapped the PPV wheels back on to S them TFU.
Had some hot wings with blue cheese, curly fries and a Snickers ice cream cup. Heading to la la land now.
I also got a rash of sh*t from co-workers, F & F about the factory rims, so I swapped the PPV wheels back on to S them TFU.
Had some hot wings with blue cheese, curly fries and a Snickers ice cream cup. Heading to la la land now.
Last edited:
