Search results

  1. kc9dre

    '03 Headlight replacement

    The wife hit a deer this morning in the Yukon and took out the driver's side headlight and turn signals and part of the grille. I could use new fog light housings as well as they was damaged from a previous owner. It is not a Denali however I am looking at various headlight types. Something...
  2. kc9dre

    Troubled 03 yukon

    When I was in the military I was taught how to solder to NASA standards I've never heard about crimping to NASA standards Sent from my SAMSUNG-SM-N910A using Tapatalk
  3. kc9dre

    Dorman SS brake line kit

    It's what I used no issues and have a 10 year warranty iirc. Sent from my SAMSUNG-SM-N910A using Tapatalk
  4. kc9dre

    Brakes

    Check the steel lines mine exploded last year when bleeding the brakes after replacing everything on the rear I bought a stainless set and have been replacing them.. you could be lucky and it is just a line going to a caliper. Sent from my SAMSUNG-SM-N910A using Tapatalk
  5. kc9dre

    Troubled 03 yukon

    As far as the low voltage aspect I have had both the battery and alternator tested and they have shown good as well. But it just takes a spike or drop for a split second to cause this issue but again tossing parts at it in hopes is getting expensive. Sent from my SAMSUNG-SM-N910A using Tapatalk
  6. kc9dre

    Troubled 03 yukon

    Yes on this particular model the TPS has to 5 volt reference signals it has two grounds and it has two signals for different signals for it to compare to see if there is a throttle mismatch I believe that was like a 1516 code or even a 15 15 15 17 but not the 1518 that I'm getting now is a...
  7. kc9dre

    Troubled 03 yukon

    Ok folks dropped it off at a shop that has had it since Thursday of last week. Stopped in to check on the problem and they can't seem to figure it out as well so it's not just me at this point... When I first got it a year ago it was getting a mismatch on the tps. Read then in this forum that...
  8. kc9dre

    Troubled 03 yukon

    It's been intermittent Bilby weeks then it will go it'll be fine and then as soon as it either gets humid or it rains is when it starts having problems as I stated earlier and I came here in hopes to find a solution that I may have overlooked . But instead I get condescending posts and replies...
  9. kc9dre

    Troubled 03 yukon

    First of all making the assumption that it's above my knowledge level is a misconception on your part I am very capable of going in and re harnessing the engine if I have to however I am looking for simple suggestions of something that I might have overlooked in the process... Sent from my...
  10. kc9dre

    Troubled 03 yukon

    Ya know I thought the point of the forums was to get suggestions... and your response is to take it to a shop... that's you auggestion... thanks for nothing... Sent from my SAMSUNG-SM-N910A using Tapatalk
  11. kc9dre

    Troubled 03 yukon

    I am to the point of walking away from GM vehicles altogether... I had an 02 Bonneville that was a nightmare with 2 engines then a transmission... and now a year into this yukon the past 5 months in have been fighting with reduced engine power intermittently however when it's humid or raining...
  12. kc9dre

    Adventures in Brakeland

    I bought the stainless dorman set no issues yet. I still have the front lines to replace in the spring as I have not yet replaced the front brakes yet...
  13. kc9dre

    Reworked the instrument cluster tonight

    The lights are under the face and there is a plastic light guide under that then you get to the lights. So unfortunately yes. However mark them with painters tape with the needles at full counterclockwise makes easy to peel off once done. Sent from my SAMSUNG-SM-N910A using Tapatalk
  14. kc9dre

    Help with wiring please

    I did the math for all 4 to begin with. 9watts each bulb... 2 bulbs per wheel Sent from my SAMSUNG-SM-N910A using Tapatalk
  15. kc9dre

    Adventures in Brakeland

    Managed to get the rear line installed yesterday. Finished the rear brake replacement after going after 2 calipers... bleeder was seized closed. the front can wait a few days enough excitement for me for a few days.... Sent from my SAMSUNG-SM-N910A using Tapatalk
  16. kc9dre

    Reworked the instrument cluster tonight

    I may have to look into that just how close to the face they sit seems to be part of the issue. Still have 4 out of the 9 that aren't lighting up was 3 so remounting one took another one out. I am wanting to do something with the face trim now. But the brakes took a toll on the cash flow...
  17. kc9dre

    Reworked the instrument cluster tonight

    I have a 2003 yukon. They have a face that has the symbols blacked out as well. Almost got that one instead but went this way with it. And the Trans gauge works without needing it programmed. Sent from my SAMSUNG-SM-N910A using Tapatalk
  18. kc9dre

    Reworked the instrument cluster tonight

    New needles have been installed. I am not a fan for the leds. They focus too much light in one place. I am going to try a different style led maybe.. the blue incandescent turn green with age. Sent from my SAMSUNG-SM-N910A using Tapatalk
  19. kc9dre

    Rear speakers...

    The front work the rear tweets work. Just not the rear doors. Tried both the factory and the dvd receiver I will look at it a bit more after brakes are done. Sent from my SAMSUNG-SM-N910A using Tapatalk
  20. kc9dre

    Rear speakers...

    2003 yukon non bose no onstar. Previous owner installed speakers and the ones in rear doors don't work. however higher tweets in the very back seem to work... How was it set up from factory? Just front doors and rear tweets? Sent from my SAMSUNG-SM-N910A using Tapatalk
  21. kc9dre

    Help with wiring please

    On my truck I have a power point close to the alternator. 5-6 amps cam safely run through a switch without a relay. There is a power point at the alternator or at a fuse box. Add in line fuse. And a switch of proper rating and your liking. You can ground to the body or run to a single ground...
  22. kc9dre

    Help with wiring please

    LEDs are best parallel. Fuse the positive. Then calculate number of units. 2 per wheel at 9watts per is 72watts. Plus 10% so let's say 80watts of power through the circuit after wires so total amps would be about 5.3 hard to find a fuse for 6 amps though so maybe a 7? Amps = watts / voltage...
  23. kc9dre

    Replacing aftermarket dvd receiver

    I am toying with the idea of getting an android based receiver for a few reasons. I want indash navigation. I want to monitor obd2 datastreams I want to add a backup camera. (So wife doesn't run anyone over) Maybe a dash cam... I want to be able to steam media without using the phone...
  24. kc9dre

    Gauges..

    Still fighting with a few LEDs but I will get that panned out in the next day or two Here are the LEDs that was sent to me. And I thought they looked a bit odd. However they fit under the clear plastic light distribution piece. A few are still not working. That could be operator error...
  25. kc9dre

    P2135 tps sensor corrolation Mismatch

    Still no errors but the truck has been sitting a week with broken brake lines. When I drove it to get the tires swapped over no errors... Sent from my SAMSUNG-SM-N910A using Tapatalk

Forum statistics

Threads
132,089
Posts
1,862,146
Members
96,555
Latest member
davidmakey230

Latest posts

Top