Search results

  1. treehan77

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Finally got the newest design GM shaft and bearing in, no more clunk. Here’s the failed OEM, and the failed from the start dorman parts. Shoulda took pic with all 3, since they are all different lol
  2. treehan77

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Mine is an 05- it’s not the same. You have to reprogram EEPROM to tell it to be on also.
  3. treehan77

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    This guy in Fort Walton Beach, FL works on clusters before 03. I'd ask him. I know he adds trans temp guages to 99-02 clusters etc. He is on YouTube as Fixed Until Broken, the about page has his email address and FB. He's the one i had add my transtemp gauge Friday- i went to his house and...
  4. treehan77

    Truck dead, starter click - Battery is Good

    First thing I would check is battery terminals and leads, they get corroded. Then the various grounds. Of course this is all IF you battery actually is good
  5. treehan77

    18” w/ knobby tries wheel combo take offs

    Dealer called me offering these new takeoffs for $850. What do you think? I’m thinking i dont really want the added noise
  6. treehan77

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Just tc-w3 lol just kidding. Pretty flat, not windy. Only 3 traffic signals in 21 miles
  7. treehan77

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Lol you noticed that huh? That was my actual mileage from there to here (about 21 miles)
  8. treehan77

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Honestly looked at it with blue and red needles, the orange were easiest to see lol. A few extra (blue) LEDs for hotspots and now I have blue turn signals lol. But finally a trans temp gauge yay!
  9. treehan77

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Well I decided on white because of 05Single lol. I can always change it later!
  10. treehan77

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Probably lay keep stock looking overlay, might do Escalade not sure yet. Which one do you like?
  11. treehan77

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Ordered the newest model intermediate steering shaft and replacement bearing, this time AC DELCO. Got impatient and went against my rule of not using dorman like a week ago and it clunks again already. ☹️ Hopefully adding transmission temp gauge tomorrow.
  12. treehan77

    Intermediate steering shaft and bearing fail

    Replaced the stupid bearing with a other dorman, no dealer had oem bearing in stock for 50 miles and I had to get it done today. Careful this time not to pop out the bearing, and it is nice and tight this time. Hopefully it lasts. The dorman ISS was fine.
  13. treehan77

    Intermediate steering shaft and bearing fail

    From where?
  14. treehan77

    Intermediate steering shaft and bearing fail

    Wow fun enough to get it in there, taking BACK out was really a PITA. It came out in three pieces, the green part, the bearings, and the plastic race retainer (?). Fun times with a pick once those last two pieces were inside the column with a shaft in the way. It sure I wanna try another...
  15. treehan77

    Intermediate steering shaft and bearing fail

    Pretty sure it shouldn’t do this when both parts are brand new ?
  16. treehan77

    Intermediate steering shaft and bearing fail

    Well i replaced the ISS and the plastic bearing thing inside. Now it’s 3x as loud and clunks a lot more lol. Maybe the actual bearing came out of the plastic thing when I was working in there? The whole shaft knocks and wobbles with my hand when I’m down there, just grabbing and shaking with my...
  17. treehan77

    Wheel Bearing?

    The dealer quoted me $450 here to do it. The part is $105. Glad you got it running though, and did t foul up too much vacation time
  18. treehan77

    Wheel Bearing?

    As long as it isn’t really full of rust, you just need a big socket etc. no real tools to buy, auto zone or advance etc will loan you the tools you need for free.
  19. treehan77

    Wheel Bearing?

    I just did both of mine with timkens for like $210. Super easy
  20. treehan77

    Smog check fail and ac quit !

    Sounds like you were lucky!
  21. treehan77

    Dashcommand or Torque Pro

    I have had dashcommand for a few years, works fine for me. I would’ve probably got torque pro, it I have iPhone and it’s android only (or used to be anyway)
  22. treehan77

    What did you do to your NBS GMT800 Tahoe/Yukon Today?

    Luckily only 44% humidity here today.
  23. treehan77

    2003 Yukon SLT still coding

    Is the intake gasket leaking. You could do a test, using propane, carb cleaner, wd40, etc. spray it around the gasket while running. If it revs up a little, it’s leaking. I think this “extra air” coming after a lot of the sensors could explain your lean condition.
  24. treehan77

    Using Dexron VI instead of Dexron III

    I’ll wait a month and see if your still works lol
  25. treehan77

    Using Dexron VI instead of Dexron III

    That’s why I’m here, to see if “should” works out for you. Mines 191k and I doubt the PO changed it.

Forum statistics

Threads
132,295
Posts
1,865,517
Members
96,880
Latest member
jvanwanz

Latest posts

Top