2007 suburban service Stabilitrack &TC light on

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

OP
OP
A

atanasd

TYF Newbie
Joined
Dec 5, 2021
Posts
15
Reaction score
5
Thank you for all feedback. What does a bad ignition coil have to do with a TC? Or I also read dirty MAF and or TB.
I think these ate secondary issues non direct to cause
 

Geotrash

Dave
Supporting Member
Joined
Feb 16, 2018
Posts
6,509
Reaction score
16,195
Location
Richmond, VA
Thank you for all feedback. What does a bad ignition coil have to do with a TC? Or I also read dirty MAF and or TB.
I think these ate secondary issues non direct to cause
Any time the computer senses that there is something wrong serious enough to prevent the engine from running at top performance, it will disable TC/Stabilitrak, hence the warning indications. That's why you need a Tech2 to diagnose it - it will show you what is preceding the TC/Stab warnings.
 

adventurenali92

Full Access Member
Joined
Feb 16, 2015
Posts
7,411
Reaction score
8,658
Location
Big Bear Lake, ca
When my service stability warning kept flashing across the info screen in my 2006, it was due to a wire shorting out that had been chewed through about a year ago, under the front passenger seat that ran to the yaw rate/accelerometer sensor, which is wired into the airbag harness under the front passenger seat. When it was in getting an oil leak fixed in October of 2020, a mouse got into it somehow while it was up on the rack overnight and chewed through the harness under my front passenger seat. I thought I’d patched up all the wires, but in November the service stability system warning kept flashing. My tech2 led me to the sensor under the front passenger seat not having to correct voltage. When I unbolted the seat there was one extra wire going into the harness that was chewed through and shorting out. Patching up that wire fixed my issue.
 

zray

TYF Newbie
Joined
Jan 14, 2018
Posts
5
Reaction score
2
I have had the same issues. This has been going on for about 2 years. Scanned and side wheel speed sensors. Replaced all 4. We were good for 6-months. Now get random and starts to shift hard. Took to get scanned when the lights were on and no codes. If will go off on its own and run fine. No check engine light ever comes on. At a total loss. I have replaced the air shocks and pump a few years ago.
 

Geotrash

Dave
Supporting Member
Joined
Feb 16, 2018
Posts
6,509
Reaction score
16,195
Location
Richmond, VA
I have had the same issues. This has been going on for about 2 years. Scanned and side wheel speed sensors. Replaced all 4. We were good for 6-months. Now get random and starts to shift hard. Took to get scanned when the lights were on and no codes. If will go off on its own and run fine. No check engine light ever comes on. At a total loss. I have replaced the air shocks and pump a few years ago.
Could be many things, including the steering position sensor. You need a scanner that can read codes from the BCM, not just the engine codes. Do you have access to a Tech2 or equivalent?
 

Ont240

Member
Joined
Apr 22, 2017
Posts
41
Reaction score
39
Location
Ontario
I had intermittent stabilitrac and TC lights as you describe on my 07 Tahoe for almost 1-1/2 years before it stayed on steady.
Knew someone with HP tuner, so we hooked up and went for a drive. Turned out to be a rear AXLE/wheel sensor was not working. Purchased one and solved the problem.
 

Forum statistics

Threads
132,705
Posts
1,872,885
Members
97,521
Latest member
Chaos49090

Latest posts

Top