Chasing a rough idle?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

OP
OP
2

2009TahoeLT

TYF Newbie
Joined
Nov 30, 2024
Posts
18
Reaction score
1
I've used the test before on older trucks at work to test of something is bad. usually you can unplug it, it default to a set value and judging by if it runs better or worse. it can help you what a direction to go in. but since I've not actually tried it on my own gm truck, is it possible it can look at the rear o2's if the front are disconnected? new one in me.


either way, my thinking is your ecm is removing 8% long term and 8% short term. that's enough fuel removed its going to run bad from being lean even if everything else is correct. so need to find out why it's doing that.

did you notice if it ran any better while the trims were at 0 while warning up?
It was still running a little rough but was a little better but it was also idling at 675-715rpms at that time. Once it settled down to the 575-615rpm area it started sputtering again worse. I checked misfires again and at idle there’s no misfires even with it running rough. But once you hit about 1100-1600 it misfires on almost every cylinder but 1 I believe
 

Attachments

  • IMG_5895.jpeg
    IMG_5895.jpeg
    217.7 KB · Views: 2
  • IMG_5896.jpeg
    IMG_5896.jpeg
    204.7 KB · Views: 2

Fless

Staff member
Super Moderator
Joined
Apr 2, 2017
Posts
11,951
Reaction score
24,334
Location
Elev 5,280
I read that you did the crank sensor relearn, but do you know if that's an OE sensor? Or if it's ever been replaced?
 

Doubeleive

Wes
Supporting Member
Joined
Nov 7, 2017
Posts
26,303
Reaction score
39,458
Location
Stockton, Ca.
I would still a do a backpressure test if a cat is clogged it will cause the misfires that are otherwise unexplained
2.5 psi is max allowable, mine had 5 psi at idle and 10 with throttle. drove normal around a city street but no power, gutless wonder

not sure if it helps but
mine didn't show up until higher rpm's (under a load) but it translated into knock retard, skip to about 1:40
I could barely get it to go over 80-85
 
Last edited:
OP
OP
2

2009TahoeLT

TYF Newbie
Joined
Nov 30, 2024
Posts
18
Reaction score
1
I would still a do a backpressure test if a cat is clogged it will cause the misfires that are otherwise unexplained
2.5 psi is max allowable, mine had 5 psi at idle and 10 with throttle. drove normal around a city street but no power, gutless wonder

not sure if it helps but
mine didn't show up until higher rpm's (under a load) but it translated into knock retard, skip to about 1:40
I could barely get it to go over 80-85
I’d have to go buy a gauge to test it. I can try and get one tomorrow
 

Doubeleive

Wes
Supporting Member
Joined
Nov 7, 2017
Posts
26,303
Reaction score
39,458
Location
Stockton, Ca.
I’d have to go buy a gauge to test it. I can try and get one tomorrow
you should be able to find something at harbor freight or make one out of stuff found there.
just needs to fit in the pre-cat 02 sensor bung
it could be something else but probably a good idea to rule it in/out as part of the troubleshooting process
 
OP
OP
2

2009TahoeLT

TYF Newbie
Joined
Nov 30, 2024
Posts
18
Reaction score
1
Also I noticed earlier when revving it to the 1100-1600rpm range to check misfires. I was getting some popping sounds from the exhaust, backfiring.
 
OP
OP
2

2009TahoeLT

TYF Newbie
Joined
Nov 30, 2024
Posts
18
Reaction score
1
you should be able to find something at harbor freight or make one out of stuff found there.
just needs to fit in the pre-cat 02 sensor bung
it could be something else but probably a good idea to rule it in/out as part of the troubleshooting process
Found this online I can pickup tomorrow. Looks like it has the o2 adapter. If this won’t work I’ll have to order off Amazon
 

Attachments

  • IMG_5900.png
    IMG_5900.png
    670.3 KB · Views: 2

Forum statistics

Threads
132,425
Posts
1,867,903
Members
97,101
Latest member
mechanic0
Top