Growing up doesn't have to suck

[randeez]

I didn't catch that! Wasn't really paying attention, though. Honestly, I was focused more on the part/ID numbers to see if I could trace them to a factory. Perhaps the same factory another (*ahem* Hellwig) has their stuff made?

they look identical to my eibach bars lol

 

[Sparksalot]

Would be nice if they spoke the same language.

Do as I say, not as I do.

 

[iamdub]

they look identical to my eibach bars lol

Aren't Eibachs hollow? Do you know the diameter and, if hollow, the tube thickness? There's SO much inconsistent info spread around the internet and when I do find specs, they're for GMT800 or '400.

 

[randeez]

Aren't Eibachs hollow? Do you know the diameter and, if hollow, the tube thickness? There's SO much inconsistent info spread around the internet and when I do find specs, they're for GMT800 or '400.

dont know...front bar prob weighs 40lbs+ so i doubt it. rear bar i havent touched since i put it on, dont remember how heavy it was

 

[iamdub]

dont know...front bar prob weighs 40lbs+ so i doubt it. rear bar i havent touched since i put it on, dont remember how heavy it was

Currently researching Eibach...

 

[randeez]

Currently researching Eibach...

looks like 35mm/33mm

 

[iamdub]

dont know...front bar prob weighs 40lbs+ so i doubt it. rear bar i havent touched since i put it on, dont remember how heavy it was

This is all I found for a 2008 Tahoe. I tried all the options in their list and only two of the six options returned any results and it was the same kit: https://eibach.com/us/983/38106.320-CHEVROLET-Tahoe-anti-roll-kit

Says 38mm/32mm and tubular.

 

[pwtr02ss]

All that girth and no grip pic. I'm....saddened.

Nice looking bars tho, for realz. I may decide to go the route when I finally get around to lowering the ol pig. Thanks for the in-depth analysis as always. Hopefully your research will save me a few bucks. We all know I could use it.

 

[iamdub]

All that girth and no grip pic. I'm....saddened.

Nice looking bars tho, for realz. I may decide to go the route when I finally get around to lowering the ol pig. Thanks for the in-depth analysis as always. Hopefully your research will save me a few bucks. We all know I could use it.

There were only two sets left on Amazon when I ordered these, so now one at $557.10. Stiffer bars are even more needed at a higher height so there's no reason to wait. You'll only need to replace the end links when you lower it. Since you're filthy rich and will be getting them, anyway, you might as well just get 'em now while they're available. You won't even feel that $600.

Here: https://a.co/d/6qKnBbQ

Here's the links you'll need to add to your drop parts. You'll need two of these: https://a.co/d/bTuWgnu

 

[pwtr02ss]

There were only two sets left on Amazon when I ordered these, so now one at $557.10. Stiffer bars are even more needed at a higher height so there's no reason to wait. You'll only need to replace the end links when you lower it. Since you're filthy rich and will be getting them, anyway, you might as well just get 'em now while they're available. You won't even feel that $600.

Here: https://a.co/d/6qKnBbQ

Here's the links you'll need to add to your drop parts. You'll need two of these: https://a.co/d/bTuWgnu

Sadly, I've splurged on gear to give you better views. I'm going to be recovering from that for a bit. My second (camera) body/lens isn't here yet...you'll be thankful.

I did buy the endlinks though. Thank you for that.

Also, Christmas IS just around the corner. I'm a size 35/33mm. Red is fine