My From Start to Finish 6.0L Build

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

OP
OP
RAMurphy

RAMurphy

Bob
Supporting Member
Military
Joined
Oct 5, 2011
Posts
1,432
Reaction score
4,545
Location
S. Maryland
89Suburban said:
So you already test drove it?
Click to expand...
Yes, it was getting late and I needed to get cleaned up. I promised my wife I would take her out to dinner prior to our granddaughters getting here. Planned to put some more miles on her after the family leaves on Sunday. She rides beautifully. Initial reaction, much more smooth and comfortable than the torsion bars. Will need to tweak settings between comfort and firm to get the ride I'm looking to achieve. I'm also going to replace the rear shocks (direct replacement of the current shock) to get that same adjustability.
 
OP
OP
RAMurphy

RAMurphy

Bob
Supporting Member
Military
Joined
Oct 5, 2011
Posts
1,432
Reaction score
4,545
Location
S. Maryland
One week later and it is time to make some minor adjustments to my coil over shocks. I most say after a week of driving I'm still quite pleased with the ride, handling and comfort. I'll post additional pictures as I make these final tweaks.
 
OP
OP
RAMurphy

RAMurphy

Bob
Supporting Member
Military
Joined
Oct 5, 2011
Posts
1,432
Reaction score
4,545
Location
S. Maryland
So, looks the my engine will be installed in September. Wanted to do it this month but work and family life pushed this out into September. So looking forward to getting this engine installed. Never, removed and installed a torque converter - any suggestions/pointers/help would be greatly appreciated.
 
OP
OP
RAMurphy

RAMurphy

Bob
Supporting Member
Military
Joined
Oct 5, 2011
Posts
1,432
Reaction score
4,545
Location
S. Maryland
Jacked up my Tahoe to make some adjustments to my coil over shocks. Glad I took the time to make these adjustments. I was riding on the bump stops just a bit and the coil over are designed not to use the bump stops in the same way as the torsion bars. After my adjustments, the ride is so much better and controlled.
20240802_101848_resized.jpg
 
OP
OP
RAMurphy

RAMurphy

Bob
Supporting Member
Military
Joined
Oct 5, 2011
Posts
1,432
Reaction score
4,545
Location
S. Maryland
Well back at it. some health issues with my better half and support that required put me behind schedule again. She is back up and around and feeling so much better. May need to retire earlier than I want so we can enjoy the time we have left in this world. Decided to prime my oil system as I move forward with my install.

First, I installed the oil filter. Then I removed the primary oil port plug. This plug I installed in the spot where the oil sending unit would install. If you forget to do this or do not install the oil pressure sending unit - all the oil will come out that orifice. Then I attached the first fitting to the block.

1.jpg

2.jpg

3.jpg
 
OP
OP
RAMurphy

RAMurphy

Bob
Supporting Member
Military
Joined
Oct 5, 2011
Posts
1,432
Reaction score
4,545
Location
S. Maryland
And so it will begin (yes, I know I'm well behind my desires on a start date (life gets in the way sometimes) . Friday I start the removal and installation of my 6.0+ engine. Took the next two weeks off to get this done among a few other changes and upgrades. Photos and status updates to follow.
 
You must log in or register to reply here.

Similar threads

ChevySSR
First oil change from 15w40 to 5w30
Replies
3
Views
510
Marky Dissod
M
B
Wiring issue - Crank, No Start
2
Replies
15
Views
2K
rockola1971
rockola1971
TexasRedNeck
2008 Tahoe LT “build” thread
2 3
Replies
20
Views
2K
Tonyrodz
Tonyrodz
M
Looking to replace my 2015 Tahoe condenser
Replies
2
Views
251
mike15tahoe
M
fondupot
New member from Charlotte, NC area
2
Replies
19
Views
968
Fless
Fless

Forum statistics

Threads
132,717
Posts
1,873,138
Members
97,542
Latest member
RRogerson

Latest posts

Top