Search results

  1. big_b_in_PA

    Stuck in 4WD?

    Did you try to take the actuator out? It sounds like maybe your front diff, or your limited slip in your diff is going bad.
  2. big_b_in_PA

    2002 Yukon Shift Interlock

    Check the brake pedal arm and see if there is an adjustment for your brake light switch, if so, move it towards you a little at a time and it should get the results you are looking for.
  3. big_b_in_PA

    mystery fuel hose disconnected

    Autoride dump hose, if you have autoride.
  4. big_b_in_PA

    Stuck in 4WD?

    The actuator is on the back side of your front axle (side closest to the engine), it has a plug with a couple wires coming out of it, and the body is a plastic or composite material. The nut part where you would put the wrench on it is pretty big, 1-1/4 1-1/2 maybe.
  5. big_b_in_PA

    Stuck in 4WD?

    Try removing the 4wd acuator on the front axle, and try manually turning the front driveshaft while the actuator is out, if it's in 2wd and the actuator is out, and it doesn't turn, you may have a bad encoder motor on your transfer case.
  6. big_b_in_PA

    Rubbing from rear with Autoride removed.

    Does your rear end sag at all? I think there's a conversion kit that includes new coil springs to compensate for the autoride shocks.
  7. big_b_in_PA

    2006 Yukon Denali radio help

    Bluefusion bfcl2k is what you are looking for. At least that's what I got from your first post. You use one of your xm channels to stream your music, you can use the steering wheel controls to take calls, and I think to make them too. But the only thing, you have to run another mic for the phone...
  8. big_b_in_PA

    2002 Tahoe Window Does Not Roll Down

    Window regulator is most likely shot. Replace it and the motor at the same time, and you should be good to go!
  9. big_b_in_PA

    Unknown brake part

    Nice, I didn't get that far.
  10. big_b_in_PA

    Unknown brake part

    This is the only thing I could find, I looked for the part number, and it's a discontinued part. The link for the part: http://parts.nalleygmc.com/products/PUMP-Vacuum-Power-Brake-Pump/3113632/89058946.html
  11. big_b_in_PA

    Unknown brake part

    I have been looking around online, I can't find any of these at all. I'm wondering of there's a way to bypass or eliminate that pump. Hopefully somebody else has had this issue and can chime in with advice.
  12. big_b_in_PA

    Unknown brake part

    From the pic shown, it looks like he doesn't have hydro boost steering, so flushing the power steering will not help him out. After a little research, that part is called an auxiliary vacuum pump, apparently when it goes bad, it acts like what you're describing.
  13. big_b_in_PA

    Lowering Keys

    But the problem is he's out of adjustment, and still needs it to go farther. I'm assuming that would work, but I don't know without seeing it. If he's doing his own work, it can't hurt to try. Either way, good luck!
  14. big_b_in_PA

    Fuel Gauge Question 03 Denali

    What he said^, and while you're in there, replace your fuel pump, too. Sometimes you can get just a sending unit without the pump, sometimes not. Just a suggestion.
  15. big_b_in_PA

    Lowering Keys

    I would try to re index the drivers side key. It may or may not solve the problem. But by the way it sounds to me, it sounds like the drivers side got indexed wrong.
  16. big_b_in_PA

    Tranny Bout gone 4L60e

    Upgrade the internals to the 5 pinion input planetary, also get "The Beast" sunshell the corvette servo, upgraded 3-4 accumulator piston, larger diameter boost valve (.500) I think, raybestos zpak clutch kit. R/v torque converter or low stall speed torque converter. Have the shift servos...
  17. big_b_in_PA

    Transfer Case not engaging 4WD - '00 Yukon

    Does the transfer case actually shift to 4low and drive in the lower gear? Or are you assuming it is by feeling the encoder motor? To me it sounds like the encoder motor drive is shot. The only way you could check this is to take encoder motor off and try to move the shaft going into the...
  18. big_b_in_PA

    Frozen lock

    Mines an 03, I know there's a difference but, in your driver info center, is there an option for driver preferences? Mine has locking and unlocking, lights on at unlock, headlight delay, mirror position, seat recall, ect. Yours may or may not have that option.
  19. big_b_in_PA

    Frozen lock

    I have an 03, and mine is completely different.
  20. big_b_in_PA

    Frozen lock

    Key fob is an easy one, take your vin to the dealership, they can give you that info, and try to sell you a new one. I have had decent luck with the ones on ebay when I've had to replace mine. ---------- Post added at 01:58 PM ---------- Previous post was at 01:54 PM ---------- You may...
  21. big_b_in_PA

    Frozen lock

    Hand sanitizer. It's alcohol based and will not freeze. Coat your key with it and stick it in your door lock and work the lock a little bit. It should help out.
  22. big_b_in_PA

    need a little more power

    Randy's ring and pinion has 4:11 sets for the front at $195-288 just two options to choose from.
  23. big_b_in_PA

    stubborn wheel hub assembly!!!!

    I took a cold chisel to the joint where the bearing assembly and knuckle meet, it takes a bit of work, but I got mine off that way.
  24. big_b_in_PA

    headliner on sunroof cover

    I had a leaky sunroof when I started, I realigned the glass so it would seal the whole way around. It's been almost two years and no leaks since.
  25. big_b_in_PA

    Spark Plugs - General Questions

    Check out the MSD wire set, they aren't much more than stock. The part number is 32829 for the set.

Forum statistics

Threads
133,018
Posts
1,878,535
Members
97,977
Latest member
Coop2015

Latest posts

Top