Aluminum / XFE NNBS Front Suspension Rebuild

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

OP
OP
petethepug

petethepug

Michael
Joined
May 4, 2016
Posts
3,025
Reaction score
3,283
Location
SoCal
Mmnn Crow. Got the ultimate humiliation and had to eat crow today. If I google 2001 s10 rear brake conversion, this comes up


How the hell did I miss the part about 1982-1992 s10 conversion? Anyone wanna buy a discounted rear disc brake conversion for their S10, s15 or blazer?
 

iamdub

Full Access Member
Joined
Apr 23, 2016
Posts
20,821
Reaction score
44,945
Location
Li'l Weezyana
Mmnn Crow. Got the ultimate humiliation and had to eat crow today. If I google 2001 s10 rear brake conversion, this comes up


How the hell did I miss the part about 1982-1992 s10 conversion? Anyone wanna buy a discounted rear disc brake conversion for their S10, s15 or blazer?

When I converted my 2002 to rear discs, I just got the setup off of a Blazer. Direct bolt-on and the abutment brackets just needed a little shimming with some Grade 8 washers. I also deleted the proportioning valve and ran the lines straight into the master cylinder, Later on, I replaced the MC with one for a Blazer.
 
OP
OP
petethepug

petethepug

Michael
Joined
May 4, 2016
Posts
3,025
Reaction score
3,283
Location
SoCal
I had read about that. I gave my Indi the green light to research what other options are out there because I obviously have too much on my plate right now. These guys are crafty on their own project so I’m sure their probably looking into the blazer swap. If not, I’ll let ‘em know it’s a thing.
 

iamdub

Full Access Member
Joined
Apr 23, 2016
Posts
20,821
Reaction score
44,945
Location
Li'l Weezyana
I had read about that. I gave my Indi the green light to research what other options are out there because I obviously have too much on my plate right now. These guys are crafty on their own project so I’m sure their probably looking into the blazer swap. If not, I’ll let ‘em know it’s a thing.

The only drawback is that you have to pull the axles to swap the backing plates. Considering the cost of the bolt-on kit versus the parts from a salvage yard or even parts store, I wouldn't consider it such a drawback. The diff fluid might need to be changed, anyway. May as well replace the outer axle bearings and seals while it's apart if those are original or leaking.
 
OP
OP
petethepug

petethepug

Michael
Joined
May 4, 2016
Posts
3,025
Reaction score
3,283
Location
SoCal
Yea, it’s apart already. I’ve never made a boneheaded move like this before. Truck is in the shop with the rear end zip tied just to move it around.
 

KidWgn

Certified Kid Hauler
Joined
Jan 11, 2023
Posts
360
Reaction score
486
Location
St. Louis, MO
Ahhhhh. The joys of modifying from original blueprint.

A wise man here at Boeing once told me:
The amount strayed from factory design is directly proportionate to the amount of time spent on jackstands.

My "fast" 04 Forester proved his theory correct.
 
OP
OP
petethepug

petethepug

Michael
Joined
May 4, 2016
Posts
3,025
Reaction score
3,283
Location
SoCal
One down, two to go. The Esky goes in next for its aluminum suspension. The s10 got its conversion with the rear discs supplied by the rears from an ‘82 Caddy Seville. Yea, bustle back disc brakes baby.

A9E6CA35-CD4A-466C-A1D3-8D06648ADD13.jpeg

It’s a 200% improvement over the OE drums. The Indy rebuilt the leaf springs, installed new shackles, bushings, hardware and feels like new shocks. It got its diff serviced and now good for another 23 years.

The anemic 15x7 OEM rims with their FOUR inch backspacing were replaced with these OEM 16x8 s15 Sonoma Hollander Reps with 235/60z tires. It got an extra inch of rubber under each corner and the tire almost 2” closer to the fender edge.
 

992dr

Full Access Member
Joined
Oct 8, 2009
Posts
3,164
Reaction score
1,209
Location
Eastern N.C.
Sorry if I missed it but my 07 PPV has aluminum lowers, steel spindle and steel uppers.
Will the aluminum upper and spindles just bolt right up?
 
OP
OP
petethepug

petethepug

Michael
Joined
May 4, 2016
Posts
3,025
Reaction score
3,283
Location
SoCal
Nope, won’t bolt up. Essentially:

Alum UCA = Alum Knuckles
Steel UCA = Steel Knucks

If your truck has steel Upper Control Arms it has steel knuckles. You’d have to swap in a set of aluminum knuckles to use alum UCA.

GM set it up so only the lower control arms can be swapped from aluminum to steel, or vis versa if your truck has steel knuckles.

Lastly, aluminum knucks need 2015-2020 tie rod ends and steel knucks use the 07-14 tie rod ends. Just to make it more confusing the 07-14 ZR1 package with both alum LCA & UCA have alum knucks from the factory with 2015+ style tie rod ends and use the typical hydraulic rack @ pinion steering set up.

What are 2015+ tie rod ends? They’re the tie rods ends with a different taper used on the 09-13 Hybrid versions of our trucks equipped from the factory with fully electric steering racks. All 2015+ trucks now have electric steering racks.

The 07-14 tie rod ends made for steel knuckles and the 15+ tie rod ends are interchangeable between the 07-14 hydraulic rack & pinion and 15-20 fully electric steering racks.

Yes, the aluminum upper control arms / UCA fit your ‘16 Yuke as long as it is fitted with aluminum knuckles or already had aluminum UCA ….

To run aluminum UCA on a truck not equipped with them you’ll need to swap the existing steel knuckles to the aluminum version. That’s what I’m doing on my ‘09 Esky

The aluminum lower control arms / LCA are interchangeable with steel on Gen 4 / 07-14 / NNBS and Gen 5 / 15-20 whether the truck has aluminum or steel knuckles.
 
Last edited:

992dr

Full Access Member
Joined
Oct 8, 2009
Posts
3,164
Reaction score
1,209
Location
Eastern N.C.
Nope, won’t bolt up. Essentially:

Alum UCA = Alum Knuckles
Steel UCA = Steel Knucks

If your truck has steel Upper Control Arms it has steel knuckles. You’d have to swap in a set of aluminum knuckles to use alum UCA.

GM set it up so only the lower control arms can be swapped from aluminum to steel, or vis versa if your truck has steel knuckles.

Lastly, aluminum knucks need 2015-2020 tie rod ends and steel knucks use the 07-14 tie rod ends. Just to make it more confusing the 07-14 ZR1 package with both alum LCA & UCA have alum knucks from the factory with 2015+ style tie rod ends and use the typical hydraulic rack @ pinion steering set up.

What are 2015+ tie rod ends? They’re the tie rods ends with a different taper used on the 09-13 Hybrid versions of our trucks equipped from the factory with fully electric steering racks. All 2015+ trucks now have electric steering racks.

The 07-14 tie rod ends made for steel knuckles and the 15+ tie rod ends are interchangeable between the 07-14 hydraulic rack & pinion and 15-20 fully electric steering racks.
Thanks for the quick reply and explanation, I appreciate it.
 

Forum statistics

Threads
132,366
Posts
1,866,800
Members
96,989
Latest member
Mreedini
Top