Rear main seal leak? Pics attached

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Blackcar

Full Access Member
Joined
Mar 31, 2018
Posts
708
Reaction score
622
My 02 Tahoe (285K mi) rains oil. This thread affirms my suspicion of the RMS. With oil at $8 a qt, I need to do something about it soon. New to Atlanta area and few tools, unfortunately. Anyone know anyone in the area who'll rent me their shop stall or garage (with tools)??

I'm also concerned about the oil flashing into a fire as it smolders on the exhaust crossover section. Has anyone seen this happen? Should I install a heat wrap on this section of exhaust until I make the needed repair?
Have you looked at valley plate seal and oil pressure sending unit at back of engine close to firewall picture to me look like oil coming down side of trans bell housing.
 

Logani

TYF Newbie
Joined
Feb 15, 2023
Posts
9
Reaction score
14
Have you looked at valley plate seal and oil pressure sending unit at back of engine close to firewall picture to me look like oil coming down side of trans bell housing.
Yes. Recently replaced knock sensors (and OP sending unit because it was accessible) as well as valve cover gaskets. Was clean in that area. I'll be redoing the job - see my other posts today - and will check it out again. I'm having to add 1.5 qts for every tank of gas. It's embarrassing.
 

Logani

TYF Newbie
Joined
Feb 15, 2023
Posts
9
Reaction score
14
On second thought, after seeing Davids vids, this could actually be my problem. I may have overlooked it when I had the intake off to replace the knock sensors. I don't think I went that far back (and down) because I wasn't actually looking for it: just a general look-over and a OP sending unit swap. Good stuff. It just seems like more than a rms and the valley plate seal would explain it. Is there pressure behind it or just lots of splashing around?
 

donjetman

Full Access Member
Joined
Oct 22, 2018
Posts
1,560
Reaction score
2,775
gen4 knock sensors are on the side of the block and they can't cause an oil leak.
 

89Suburban

Bull in the china shop
Supporting Member
Joined
Jan 10, 2013
Posts
15,329
Reaction score
42,705
Location
SE PA
On second thought, after seeing Davids vids, this could actually be my problem. I may have overlooked it when I had the intake off to replace the knock sensors. I don't think I went that far back (and down) because I wasn't actually looking for it: just a general look-over and a OP sending unit swap. Good stuff. It just seems like more than a rms and the valley plate seal would explain it. Is there pressure behind it or just lots of splashing around?


If you have DOD/AFM the valley cover does have pressure in it.
 

91RS

Full Access Member
Joined
Nov 15, 2009
Posts
2,594
Reaction score
2,045
Location
GA
Yes. Recently replaced knock sensors (and OP sending unit because it was accessible) as well as valve cover gaskets. Was clean in that area. I'll be redoing the job - see my other posts today - and will check it out again. I'm having to add 1.5 qts for every tank of gas. It's embarrassing.

You have oil consumption, not a leak. If you were leaking 1.5 quarts of oil every tank of fuel (300 miles or so), the entire underside of your truck would be drenched in oil and your driveway would be black. You could take it to Canada and it would never rust.
 
OP
OP
M

m1dn

Full Access Member
Joined
Jun 15, 2022
Posts
178
Reaction score
316
If you have DOD/AFM the valley cover does have pressure in it.
Wouldn’t it have pressure without dod anyway since oil pressure sensor is there? Mine is without dod but was pissing oil everywhere around the cover
 

Blackcar

Full Access Member
Joined
Mar 31, 2018
Posts
708
Reaction score
622
On second thought, after seeing Davids vids, this could actually be my problem. I may have overlooked it when I had the intake off to replace the knock sensors. I don't think I went that far back (and down) because I wasn't actually looking for it: just a general look-over and a OP sending unit swap. Good stuff. It just seems like more than a rms and the valley plate seal would explain it. Is there pressure behind it or just lots of splashing around?
If you're talking about oil pressure sender there is no pressure if engines off but will leak when running.
 

Logani

TYF Newbie
Joined
Feb 15, 2023
Posts
9
Reaction score
14
You have oil consumption, not a leak. If you were leaking 1.5 quarts of oil every tank of fuel (300 miles or so), the entire underside of your truck would be drenched in oil and your driveway would be black. You could take it to Canada and it would never rust.
I didn't exaggerate. Will post pictures of my well-preserved undercarriage and the oil slick on my back doors/glass tomorrow. It drips faster than a woman crying while watching a Lifetime movie. When I pull in to Walmart (to buy more oil) in the rain, rainbow dots lead the way to my Tahoe like a Pac Man maze. Gretta Thunberg would put a hit out on my if she knew what a mess I was making. More pics to follow.
 

Attachments

  • 20230313_100259.jpg
    20230313_100259.jpg
    208.4 KB · Views: 12
  • 20230314_151530.jpg
    20230314_151530.jpg
    591.8 KB · Views: 8
  • 20230314_143522.jpg
    20230314_143522.jpg
    365.8 KB · Views: 8
  • 20230314_143527.jpg
    20230314_143527.jpg
    417.4 KB · Views: 8
  • 20230314_123045.jpg
    20230314_123045.jpg
    709 KB · Views: 8
Last edited:

Forum statistics

Threads
132,732
Posts
1,873,331
Members
97,563
Latest member
bmead21
Top