"Reduced engine power"

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

kayakfish247

TYF Newbie
Joined
Oct 26, 2024
Posts
3
Reaction score
5
hey guys. So I'm new here. I have a 2003 with a 5.3 Vin z. It's probably thw best running engine I've ever owned. But is has the dreaded p1516 p0120 p0220 which are all with the tac module throttle body and throttle pedal position. I've replace the tac, throttle body, tps on the pedal, cleaned the intake temp sensor replace the mass air sensor, and ran a ground wire from the throttle body to the ecm to tac and to the engine then to the body. Also cleaned the ground junctions at the lower driver's side body and behind the head. It still throws intermittent faults listed above while driving and goes into reduced engine power. I leave a scanner connected and clear the fault and it goes back to normal. Seems to do it alot more when it rains and it's cold outside. Lately it's been doing it at highway speeds. More often when idling. Anyone got any ideas? Pretty much only thing left is an engine harness which I believe is the issue. Thanks ahead of time.
 
Last edited by a moderator:

Joseph Garcia

Supporting Member
Joined
Aug 2, 2018
Posts
7,340
Reaction score
9,919
Welcome to the Forum from NH.

Lots of knowledgeable folks here who freely share their knowledge, experiences, and perspectives. Knowledge is power.

I hope that you will become a participating member in the Forum's discussions.

Pics of the truck, please.

You are already receiving sage advice from the knowledgeable folks on this Forum, and other members will chime in.
 

strutaeng

Full Access Member
Joined
Aug 10, 2023
Posts
1,178
Reaction score
2,444
Location
Dallas, Texas
Find a wiring diagram and back probe the pins at the ECU and run temporary wires to the TAC/throttle body. See if that makes any difference.

You will basically have another set of wires in parallel, so if there's issue on the main harness, the temporary wires will prevent the intermittent loss of signal triggering the code.

If the problem goes away, then you know where the problem lies.
 

Fless

Staff member
Super Moderator
Joined
Apr 2, 2017
Posts
11,854
Reaction score
24,110
Location
Elev 5,280
Hey thanks for the reply. No but I did re-pin the connectors on the throttle body and the tac module but like I said I believe it has a wire breaking down.

As @ScottyBoy noted, the wires to (especially) the throttle body are prone to breaking underneath the insulation. If a careful inspection hasn't been done, suggest doing it from the TB back about a foot. You may not see a broken wire, so check them by flexing and by feel. A new pigtail might solve it. I think it was @89Suburban who cured his this way.
 
OP
OP
K

kayakfish247

TYF Newbie
Joined
Oct 26, 2024
Posts
3
Reaction score
5
Find a wiring diagram and back probe the pins at the ECU and run temporary wires to the TAC/throttle body. See if that makes any difference.

You will basically have another set of wires in parallel, so if there's issue on the main harness, the temporary wires will prevent the intermittent loss of signal triggering the code.

If the problem goes away, then you know where the problem lies.
That actually sounds like a good idea. Definitely try that. I actually have terminals I can use to run a new temp harness. Thanks
 

89Suburban

Bull in the china shop
Supporting Member
Joined
Jan 10, 2013
Posts
15,081
Reaction score
41,724
Location
SE PA
Thanks @Fless yeah my pigtail had been replaced by somebody and the connections took a crap so I re-soldered them and she has been fine since. Some pics here. Was a ***** to figure out I almost said hell with it and got rid of her.

 

rockola1971

Full Access Member
Joined
Dec 29, 2016
Posts
2,605
Reaction score
3,512
Location
Indiana (formerly IL)
Very common failure after the dreaded dead spot in the TPS position trace within the TPS. Then comes the Pigtail plugged into the TPS (They make a replacement that you just splice in) and then finally the harness that plugs into the the TAC Module itself. All 3 of these will cause the dreaded reduced engine power individually or collectively.
 

Forum statistics

Threads
132,301
Posts
1,865,639
Members
96,885
Latest member
BinOdhaib
Top