What did you do to your NBS GMT800 Tahoe/Yukon Today?

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

osiris94ej

Full Access Member
Joined
Apr 2, 2016
Posts
469
Reaction score
658
Location
Casper Wyoming
Is there a specific resistor to use for the tail lights ? Ohms ? Or will any one work? My tails flash too fast and of course no cruise. Thx in advance.
iJDMTOY 50W 6-Ohm Load Resistors For LED Turn Signal Light Bulbs Solve Fix Hyper Rapid Flash https://www.amazon.com/dp/B00FDX6YAE/ref=cm_sw_r_other_apa_xtaOxbMMTM4TQ

Pretty sure Auto Zone, O'Really, or Advanced should have them too. At least all 3 here have them on the shelf. Or other option is to buy an led flasher. That's what I did and no problems so far.

Sent from my SM-N920V using Tapatalk
 
Last edited:

pnwdan

Cunning linguist
Joined
Aug 17, 2014
Posts
347
Reaction score
127
Location
Arlington, WA
Saturday my Denali started chirping around the belt area. A little digging with a stethoscope led me to the water pump. Even though it was new in December, I decided to replace it. After installing the sound came back. Still chirping at the water pump. Further digging I found the the pulley on the power steering pump had slightly walked outward causing belt misalignment and causing the belt to chirp as it was forced to line up with the crank pull your after coming off of the water pump. I decided to replace the power steering pump since it had shafts play. Now after 2 days of on and off chasing, I'm done.
 

Tonyrodz

Resident Resident
Joined
Feb 16, 2012
Posts
31,623
Reaction score
47,151
Location
Central Jersey

Rocket Man

Mark
Supporting Member
Joined
Dec 25, 2014
Posts
26,004
Reaction score
50,862
Location
Oregon
I can't wait till I do this upgrade !!! Any far away pics? Should fill up that area nicely behind those big shoes.
I'll get some pics from a ways back tomorrow, been a busy day today and now it's dark!

Well here you go, lunchtime pic.

image.jpg
 
Last edited:

Martinjmpr

Full Access Member
Joined
Jun 4, 2015
Posts
378
Reaction score
184
Location
Littleton, Co
Got a few things done this weekend. Removed and reinstalled my driver's side LED fog light. When I installed it back in April I ran the power wire through the same hole as the mounting bolt and as a result it was slightly crooked. Drove my crazy but I knew that in order to fix it I'd have to unbolt it, pull the wiring apart, drill a hole for the wire and then reassemble, but I finally had the time to do it. Looks much better I think.

Before:

2016-04-24%2017.13.58_zpsxjigtide.jpg

After:

2016-07-30%2017.03.45_zpsxocu4imm.jpg

Looks much better I think.

Other weekend projects: Installed the battery tray for the 2nd battery:

2016-07-30%2017.04.24_zpsmalygzvn.jpg

I've got most of the other parts I need minus the battery and the cables. Will work on that next week.

Also had the tires removed from the wheels I bought in March. Tried to clean up the wheels but they're still pretty yellowed.
 

Rocket Man

Mark
Supporting Member
Joined
Dec 25, 2014
Posts
26,004
Reaction score
50,862
Location
Oregon
I can't wait till I do this upgrade !!! Any far away pics? Should fill up that area nicely behind those big shoes.
Installed the rear stainless steel brake hoses but I admit I did not do the one that goes from the differential to the body; I couldn't see any way to get to the top fitting that's above the spare tire mount. @05Single here's a couple of pictures of the GMT900 brake upgrade from back a ways. And a shot of the rear hoses because we all know "if there's no pictures, it didn't happen" lol.

IMG_5328.JPG

IMG_5330.JPG

IMG_5331.JPG
 

05Single

afraid of the dark
Joined
Feb 26, 2015
Posts
8,186
Reaction score
11,456
Got a few things done this weekend. Removed and reinstalled my driver's side LED fog light. When I installed it back in April I ran the power wire through the same hole as the mounting bolt and as a result it was slightly crooked. Drove my crazy but I knew that in order to fix it I'd have to unbolt it, pull the wiring apart, drill a hole for the wire and then reassemble, but I finally had the time to do it. Looks much better I think.

Before:

2016-04-24%2017.13.58_zpsxjigtide.jpg

After:

2016-07-30%2017.03.45_zpsxocu4imm.jpg

Looks much better I think.

Other weekend projects: Installed the battery tray for the 2nd battery:

2016-07-30%2017.04.24_zpsmalygzvn.jpg

I've got most of the other parts I need minus the battery and the cables. Will work on that next week.

Also had the tires removed from the wheels I bought in March. Tried to clean up the wheels but they're still pretty yellowed.
Where you pick up that tray from ?
 

Martinjmpr

Full Access Member
Joined
Jun 4, 2015
Posts
378
Reaction score
184
Location
Littleton, Co

Forum statistics

Threads
132,377
Posts
1,867,013
Members
97,012
Latest member
Roscoe2352

Latest posts

Top