Search results

  1. YUOnDaGround

    Front door Speakers

    First off I have search and I couldn't find an answer. 1. Dealing with the front door speakers, there seems to be two speaker mounts in the door. Is this an option from one stereo to another? As in cheaper systems get smaller speakers and the better systems get bigger speakers? 2. I ask this...
  2. YUOnDaGround

    Rattle at High RPM's - Anyone know?

    Good point.
  3. YUOnDaGround

    Rattle at High RPM's - Anyone know?

    I may end up changing out the o2 sensors just to see what happens.
  4. YUOnDaGround

    Rattle at High RPM's - Anyone know?

    Only while driving while at wot at high rpms and I haven't noticed a difference related to ac being off or on.
  5. YUOnDaGround

    Rattle at High RPM's - Anyone know?

    I use CRC maf cleaner for the maf and I use Generic Throttle body cleaner for the TB.
  6. YUOnDaGround

    Rattle at High RPM's - Anyone know?

    When you say better quality gas do you mean octane or gas station? As in shell over a bottom of the barrel no name gas station? Also, I have cleaned the maf multiple times... However I will clean it again just to make sure. When I say multiple I mean 3-4 times in the last 2 months...
  7. YUOnDaGround

    Rattle at High RPM's - Anyone know?

    none at all
  8. YUOnDaGround

    Rattle at High RPM's - Anyone know?

    When I stomp on the throttle and rev it up around 4-5k rpms there is a noticeable rattle from the engine. Enough to notice above the cool-air-intake and above my magnaflow exhaust. Could this be the valves out of adjustment? Anyone had this happen to them before? Thanks for your input. 2002...
  9. YUOnDaGround

    An emergency fix for a fuel pump

    I have a different theory. I think that it is the screen around the pump getting dirty and not letting fuel through. You beat the gas tank and it shakes the sediment/dirt off the screen just long enough to let the fuel pump prime the fuel rail and start the truck. Mine did this when it...
  10. YUOnDaGround

    Blizzardx23's Pick-n-Pull thread

    Blizzard just created a monster.
  11. YUOnDaGround

    Seafoam, bad MPG after use?

    I had good luck with my treatment. 1 to 1.5 mpg increase.
  12. YUOnDaGround

    Antifreeze pouring out of passenger side wheel area

    edit
  13. YUOnDaGround

    Got $1000 to spend...what should I get...

    I would look around for a cheap AR15 or an AK47 modded out
  14. YUOnDaGround

    Changing rotted backing plates/dust shields

    I was looking at the project again of replacing the backing plates and can somebody tell me what is the actual function and purpose of the backing plates?
  15. YUOnDaGround

    Engine Stumbles only in gear and only at idle

    1. I verified the gap on the plugs with my feeler gauges, a couple were off a little so they had to be adjusted (one was too wide and one too narrow). My feeler gauges are incredibly smooth and couldn't scrape off the coating IMO. - I don't use the 'gauge wheel' type. 2. The MAF is plugged in...
  16. YUOnDaGround

    Engine Stumbles only in gear and only at idle

    My engine when I first start it up idles fine but when I put it into gear it stumbles every 5 seconds. I do not have any codes. So I don't think it is an intake gasket. FYI I just changed sparkplugs (gapped to .040") to AC Delco Iridium and I have a K&N CAI. Any ideas? Yes this just started...
  17. YUOnDaGround

    help with 2001 tahoe

    I don't know if you've figured this out yet or not, but I spoke with the onstar people today and they said that my 2002 Tahoe cannot be converted from analog to digital. So now I don't have and cannot get Onstar service.
  18. YUOnDaGround

    School me on Performance/Cold Air Intake Systems

    It would seem to me that this scoop would show itself to be useful during 1. High speed >65 driving for gas mileage increase. ~1mpg increase 2. Wide open throttle at higher speeds. Plus this seems like a pretty good warranty.
  19. YUOnDaGround

    Uneven Brake wear on rotor, pulls to the right.

    Ok I got new brake pads, DuraLast Gold CMax ceramics and got to the shop. When I went to take the calipers and wheels off I realized that the last guy had installed the shims/brake hardware in on the upper and lower ends of each caliper to hold the brake pad in place. They are nice and designed...
  20. YUOnDaGround

    DIY: Tahoe Rear Brakes

    That EFFFING happened to me! I got new pads and rotors put on by a local shop and now the thing pulls hard to the right everytime I brake. I am putting new pads on tonight...the right way.
  21. YUOnDaGround

    Uneven Brake wear on rotor, pulls to the right.

    New rotors and pads put on by a local shop about 2 months ago.
  22. YUOnDaGround

    Uneven Brake wear on rotor, pulls to the right.

    Anyone ever notice that your brake rotor surface isn't totally shinny? Yes a very general question but here's what is going on. 1. When I apply brakes at any pressure it pulls to the right. 2. There is a rust ring (much the same as if you were to leave your truck sitting for about a...
  23. YUOnDaGround

    why not to install Headlight tint!!!

    Edit.
  24. YUOnDaGround

    Zert fitting install on ISS

    Thumper, Where did you intall your zerk fitting? Is it closer to the retainer bolt or the firewall. I see that it 'neck downs' in two places. I'm just wondering what side of the smaller part you installed it on. Thanks. Bruce
  25. YUOnDaGround

    Lubing your intermediate steering shaft for 1999 to 2004 trucks

    Are you talking about the grand prix or the girlfriend?

Forum statistics

Threads
131,412
Posts
1,850,607
Members
95,505
Latest member
Burgy

Latest posts

Top